Dynamic CCTV DVR-8 Panduan Pengguna - Halaman 14

Jelajahi secara online atau unduh pdf Panduan Pengguna untuk DVR Dynamic CCTV DVR-8. Dynamic CCTV DVR-8 18 halaman. 8 channel digital video multiplex recorder

Halaman Cetak

8 channel stand-alone DVMR

ALL ABOUT IMAGE RECOGNITION & PROCESSING

3-2. Recording

1. PLAY

Indicates camera title.

Changes to Playback Mode from

Default title is CH-1, CH-2, ...

CH-8. You can change camera

Recording. If pressed shortly, playback

tile in EDIT CAMERA TITLE in

starts from the stop point in previous

CAMERA SETUP.

operation.

If pressed for a long time, you can enter

into GO TO MENU and select by

PERCENT, TIME/DATE, or EVENT LIST

the point from which you want to replay.

Refer to Playback part(PAGE.13)of this manual

for details.

2. MODE

Changes screen division in the sequence of full

screen of specific channel, 4-split screen, and 9-

split screen whenever pressed.

If it is pressed for a long time, it changes type of

monitor from COMPOSITE to VGA or VGA to

COMPOSITE in case VGA option board is

included in the DVMR package. In case you

connect CRT type PC monitor to DVMR

unit, and monitor type is set at

COMPOSITE, pictures displayed shall

be flickering.

1. Indicates address of camera

3. P/T

(channel number from 1 to 8)

Change by pressing [UP] or

In case you connected PTZ camera to

[DOWN] button

any channel of DVMR unit, press [P/T] button first

to control this camera using operation buttons on

the front panel.

Be sure to select model of PTZ camera whose

protocol is already incorporated into DVMR

system. Model of PTZ camera whose protocol

incorporated is PELCO D type, DRX-502A.

CH-01

For PTZ camera whose protocol is not built-in

protocol, you have to input protocol of that

camera in USER DEFINE /PAN/TILT CMD

CH-04

SEPUP/MISCELLANEOUS SETUP.

After pressing [P/T] button, command with channel

number(from 1 to 8) in front is displayed whenever

CH-07

you press [LEFT] or [RIGHT] button.

Select channel number first by pressing [UP] or

[DOWN] button, and select command by pressing

[LEFT] or [RIGHT] button.

Then, PTZ camera will move as per command you

selected as far as you press [ENTER] button.

Press [P/T] button once more to stop PTZ camera control.

3. OPeration

Indicates date and current time.

YY / MM / DD

Indicates operating status

Hr/Min/Sec

: Recording

: Standby for recording

: Backward/Forward

: Fast backward/forward

Indicates status of

recoding and

playback

TIM : Continuous

CH-01

CH-02

CH-03

recording

MOT : Motion

recording

ALM : Alarm

recording

CH-04

CH-05

CH-06

R : Indicates how

many % of total

03 / 10 / 25

HDD space is

16 : 11 : 38

recorded.

TIM

12.34%

P : Indicates what is

CH-07

CH-08

5.03%

starting point of

next playback,

unless you skip to

specific point in

GO TO MENU.

Recording Mode

Select command by

pressing [LEFT] and

[RIGHT] button

POWER ON

POWER OFF

PAN LEFT

P / T

PAN RIGHT

1. PAN RIGHT

TILT UP

CH-02

CH-03

TILT DOWN

P/T LEFT-UP

P/T RIGHT-UP

P/T RIGHT-DOWN

P/T LEFT-DOWN

CH-05

CH-06

ZOOM IN

03 / 10 / 25

ZOOM OUT

16 : 11 : 38

TIM

FOCUS FAR

12.34%

FOCUS NEAR

CH-08

5.03%

FOCUS AUTO

IRIS OPEN

IRIS CLOSE

IRIS AUTO

AUTO SCAN

GO TO PRESET

PAN/TILT Control

SET PRESET

(Ex: PELCO D type)

CLEAR PRESET

PAN/TILE STOP

8 channel stand-alone DVMR

ALL ABOUT IMAGE RECOGNITION & PROCESSING

3) TIME INTERVAL

TIME INTERVAL implies recording speed, and 1/1

represents maximum recoding speed of this DVMR

system, that is 60 fields/sec in total.

When half-tone green bar is on TIME INTERVAL, press

[LEFT] or [RIGHT] button to select recording speed you

want.

TIME INTERVAL set here is applied for all RECORDING

TYPE, that are, TIMER, MOTION, or ALARM.

Recording speed for each TIME INTERVAL is as follows.

(based on NTSC system)

1/1 x : 60 fields/sec in total

1/2 x : 30 fields/sec in total

1/3 x : 20 fields/sec in total

1/ 4 x : 15 fields/sec in total

and so on

4) EVENT OFF TIMER

EVENT OFF TIMEER sets time interval between event(video loss, motion detected, and alarm)

to event not to enlist envent which happen too frequently.

For example, if you set EVENT OFF TIMER at 60 sec, and motion detected now is detected less than 60 sec

after previous motion, it is not enlisted in event list. However, motion detect now is after more than 60 sec, it

is enlisted in event list. It is same for alarm or video loss.

EVENT OFF TIMER is to restrict event to be enlisted in event list, and it is useful in case you set recording

mode at motion detection mode, alarm mode.

In case motion is detected very frequently, event list shall be full with just motion detected, and it is

meaningless to have such event list.

Default value set by manufacturer is 60 sec.

5) REFRESH RATE

When you record in motion recording mode, and motion is detected in one of 8 channel and no

motion is detected in all other channels in some times.

In this case, we may see pictures fairly long hours ago in playback in channels where no motion

is detected, while pictures in a channel where we have many motion detected is updated very

frequently.

Refresh rate is time interval for recording pictures from channels where no motion is detected for

a long time. That is, even though there is no motion detected, DVMR system records an image

as per this REFRESH RATE time interval to show relatively recent pictures in corresponding

channels, even though there are no motions detected.

6) DURATION

It is motion duration or alarm duration. When DVMR records in motion recording mode or alarm

recording mode, it records for DURATION time in case motion is detected or alarm is activated,

respectively.

4. Configuration

RECORD SETUP

RECORD TYPE

TIMER

OVERWRITE

TIME INTERVAL

1/1 X

EVENT OFF TIMER

60 SEC

REFRESH RATE

------

DURATION

------

SELECT

, PRESS

RECORD SETUP