DynaQuip Controls WaterCop classic Panduan Pemilik dan Panduan Instalasi - Halaman 10

Jelajahi secara online atau unduh pdf Panduan Pemilik dan Panduan Instalasi untuk Pengontrol DynaQuip Controls WaterCop classic. DynaQuip Controls WaterCop classic 12 halaman.

Halaman Cetak

Choose a dry location to install the WaterCop

see what position the valve is in (open/closed) and accessible for resetting after a leak has been detected

and corrected, and for checking and resetting the radio receiver code if necessary . Place the valve where

the housing is protected from use as a step or other excessive loads . The shut-off valve must be installed:

•

In the main water line;

•

Just downstream from the main water shut-off valve;

•

In a dry location (indoors only);

•

Where it is accessible for checking and resetting the valve and for resetting the radio receiver code, if necessary; and

•

Where the case is protected from use as a step or other excessive loads .

Caution:

Never use the housing for leverage when mounting this unit or tightening fittings. Use a wrench on

the valve flats that are provided.

Caution:

High heat from soldering or brazing can damage valve seats or motor housing. Proper precautions

should be taken to prevent damage from heat when installing the unit. Remove plastic housing before

soldering valve in place.

Additional Part Requirements

Installation of the WaterCop

WaterCop

, new fittings will be needed to connect the ends of the piping to the WaterCop

The type of connecting fittings to use will be determined by the type of existing piping, local plumbing codes, and

"industry standard practices . "

The most common material for water supply lines is copper . If the WaterCop

have a choice of fittings and methods of installation .

Compression Fittings

The unit can be installed with compression fittings using common household tools and basic mechanical ability . You will need:

a) 2 fittings (male pipe thread x compression)

available at most local hardware or plumbing supply stores

b) Teflon

tape or other thread sealant

c) Tubing cutter

Measure the outside diameter of the copper tube and note the valve size to be sure you purchase the proper size fittings

for the job .

1 . Remove nuts and sleeves from compression fittings and install the fittings into each end of the valve using Teflon

tape or other thread sealant to ensure a watertight seal . Hold one wrench on flats of valve body and use the other to

tighten fittings .

2 . Measure the distance from end to end of valve assembly . For 1/2" tube (5/8" outside diameter) subtract 1/2", for 3/4"

tube (7/8" outside diameter) subtract 3/4" from your measurement . This is the length of the section of tubing to be

cut out of the existing line . The piece of existing tubing to be cut out is shorter than the measured length so that tube

ends extend into the compression fittings .

3 . Select the location for the WaterCop

unit . After cutting the section of tube out of the line, you will need to shift the tube ends to be able to fit the unit into

place . Make sure you will have access and room to adjust before you cut the tube .

4 . Mark the tube in the location you have selected . Double check the length and location you marked .

5 . Turn water off and drain the system .

6 . Use tube cutter to cut copper tube at the locations you marked . Careful, there will probably still be some water

in the line .

7 . Remove any burrs from the tube ends and clean ends .

DynaQuip Controls • 10 Harris Industrial Park • St. Clair, MO 63077

Tel. 800-545-3636 • Fax. 636-629-5528 • www.watercop.com

. The front control panel should be easily visible in order to

will require additional parts . When the main supply line is cut to accommodate the

. Be sure to consider that you will need access to the front panel of the control

valve .

is to be installed in a copper line, you still

d) Ruler

e) Pencil or marker

f) 2 large adjustable wrenches

WARNING

DO NOT USE ON FIRE

SPRINKLER SYSTEMS