Decko 24000-DKO Panduan Pemilik - Halaman 12

Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Pembuka Pintu Garasi Decko 24000-DKO. Decko 24000-DKO 14 halaman. Handles doors 18 ft. wide & up to 7ft.tall

Halaman Cetak

1. Operating the Opener

Wiring Instructions

To prevent SERIOUS INJURY or DEATH from electrocution:

- Power MUST NOT be connected until instructed.

- NO exposed part of the wire should be visible outside of the terminal for proper connection.

Open

Wire Terminals

Screwdriver or similar tool

Fig. 1

Insert into unit

Outside

1/2"

Actual size

Fig. 2

Fig. 3

WARNING

In the following section, the Photo Eye Safety System will

be connected to the Opener. Please read and understand

the wiring instructions before connecting wires.

The connection terminals on the rear panel of the Opener

are used to connect wires from accessories.

To connect a wire to an assigned terminal, use a small "flat

head" screwdriver to push in the orange tab on the Wire

Terminal as shown in Fig.1.

Insert approximately 1/2" (13mm) of the wire into the

terminal while pushing in the tab as shown in Fig.2.

Wires MUST NOT be frayed and connected properly as

shown in Fig.3. Each accessory requires a pair of

terminals, Each pair of terminals MUST be connected with

one white wire and one striped wire (non-polarized) from

the SAME accessory.

Check for proper connection by gently pulling on the wire.

The wire should not come out of the terminal. NO exposed

part of the wire should be visible outside of the terminal.

Use the insulated staples provided to secure the wires to

the wall and/or ceiling. Be careful not to damage the wires

while securing the staples.

Wires to the terminals on the Opener

Min. 5 feet (1.5m)

above floor

Photo Eye Safety System

Suggested placement of insulated staples

Force Adjustment

To prevent SERIOUS INJURY or DEATH from improper Force Adjustment:

- DO NOT adjust force to compensate for binding or sticking of the garage door. Call a qualified garage

door service technician to make necessary adjustments in case of binding.

- DO NOT increase the force beyond minimum force required for closing the door. Too much force will cause

improper operation of safety reversal mechanism.

- If either the Force or Travel limit adjustment is made, the other adjustment may also needed.

- After ANY adjustments, the Safety Reverse Test MUST be performed to ensure the door reverses on

contact with a 1-1/2" thick object (2x4 laid flat) .

For safe operation, the force setting should

always be set at the MINIMUM FORCE

required to run the door.

Terminals

Wall Panel

WARNING

Adjusting Force

1. Force Adjustment controls are located on the rear panel of

the Opener. The force adjustments regulate the amount of

force required to open or close the door.

2. Force Adjustment is applied only to compensate for the minor

resistance caused by weather or other means.

 Note: Force is preset at level 6 for both Open and Close

adjustments. The size and operating conditions of the

garage door will determine the correct level of Force/

Sensitivity. Weather conditions may also affect the operation

of the door requiring further adjustments as needed.

 Note: If the close force is set too light the Opener will reverse

the door during closing. If the open force is set too light the

Opener will stop the door during opening.

 Note: There are 12 levels for open and close force settings.

When either the maximum or minimum level is reached, the

light will flash 6 times.

 Never adjust the force setting by more than 1 level (1 press)

at a time.

Setting Force

Setting Close Force

1. If the door completes a full close cycle without reversing,

decrease (-) the Close Force by 1 level at a time until the

door reverses. If the door reverses during closing, increase

(+) Close Force by 1 increment. The Close Force is now

properly adjusted.

2. During the "door-close" cycle, the Opener will reverse if the

force required to close the door is exceeded.

Setting Open Force

1. If the door completes a full open cycle without stopping,

decrease (-) the amount of force by 1 level until the door

stops during the opening. Once the door stops during

opening, increase (+) Open Force by 1 increment. The Close

Force is now properly adjusted.

2. During the "door-open" cycle the Opener will stop if the force

required to open the door is exceeded.