Briteq BT-SUNRAY 130R Panduan Pengoperasian - Halaman 6

Jelajahi secara online atau unduh pdf Panduan Pengoperasian untuk Proyektor Briteq BT-SUNRAY 130R. Briteq BT-SUNRAY 130R 17 halaman. 130watt dtw blinder high cri expo projector

Halaman Cetak

ENGLISH

7. HANGING BRACKET: with nuts for the use of the (optional) Briteq Omega Bracket Small (code: 02677).

You can use the hole in the center of the bracket to fix a hook or truss clamp.

8. SAFETY EYEBOLT: used to attach a safety cable when the unit is rigged (see paragraph "overhead

rigging"

9. OMEGA BRACKETS: use these holes to install a Briteq

10. MOUNTING FRAME: used to install the different accessories that are included. When you use these,

always make sure that the safety clip is well closed and located on the upper side before you install the

projector!

11. BLINDER GLASS: to be installed when the projector is used as blinder to give a special "retro" effect.

12. COMPOUND EYE LENSES: two different lenses (15° and 35°) can be installed to narrow the beam

while the projector is used as EXPO projector.

13. GEL FRAME: since this projector only produces white light, the gel frame can be used to install optional

CTO / CTB / COLOR filters when needed.

14. GLARE SHIELD: used to make a better aligned beam and/or avoid unwanted glare. Can be used in

combination with the lenses or gel frame.

15. BARNDOORS: (optional part: order code: 05527) can be installed to delimit the beam in certain

directions. Can be used in combination with the lenses or gel frame.

SETUP MENU:

The setup MENU of this projector was deliberately kept very simple to allow quick installation with less risk of

incorrect settings. In addition, a number of important settings are made via a DMX control channel.

Press the MENU-button to enter the setup MENU.

• Use the ▼/▲ buttons to browse the MENU until the required function shows up.

• Select the function with the ENTER-button.

• Use ▼/▲ buttons to change the values.

• Press the ENTER-button to confirm the selected value.

ADDRESS

Used to set the desired DMX-address.

• Use the ▼/▲ buttons to browse the MENU until the required function shows up.

• Use ▼/▲ buttons to select the desired DMX512 address.

• Once the correct address shows on the display, press the ENTER-button to save it.

Remark: on RDM-compatible controllers this option can also be remotely set.

CH. MODE

Used to set the desired channel mode.

• Use the ▼/▲ buttons to browse the MENU until the required function shows up.

• Select the function with the ENTER-button.

• Use ▼/▲ buttons to select the desired mode:

• BLIND 8b:

4 channel mode for full control in 8bit mode.

• BLIND 16b: 6 channel mode for full control in 16bit mode.

• EXPO WW:

1 channel 8bit mode, 3000K without red shift halogen effect.

• EXPO DTW: 1 channel 8bit mode, with red shift halogen effect.

• Once the correct option shows on the display, press the ENTER-button to save it.

Remark: on RDM-compatible controllers this option can also be remotely set.

ST.ALONE DIMMER

Used to set the dimmer level while used in standalone mode.

• Use the ▼/▲ buttons to browse the MENU until the required function shows up.

• Select the function with the ENTER-button.

• Use ▼/▲ buttons to set the desired dimmer level

• Once the correct dimmer level shows on the display, press the ENTER-button to save it.

Remark: this option can only be used while the NO DMX behavior is set to ST.ALONE

BRITEQ

Omega Bracket Small (code: 02677).

4/12

OPERATION MANUAL

BT-SUNRAY 130R