Gardeline GL 480 SP Panduan Memulai dengan Cepat - Halaman 16

Jelajahi secara online atau unduh pdf Panduan Memulai dengan Cepat untuk Mesin Pemotong Rumput Gardeline GL 480 SP. Gardeline GL 480 SP 19 halaman.

Halaman Cetak

Operator Manual

General assembly

information

If you have any problems

assembling or using this mower

please call our Helpline on:

0845 600 2912

For instructions regarding the engine

and the battery (if supplied), read the

relevant manuals.

NOTE – The machine can be supplied with

some of the components already fitted.

1. FINISH ASSEMBLY

1.1 To mount the stone-guard (1), the left

end of the pin (2) must be pushed

through and then inserted in the hole of

the left-hand (3) on the chassis. Line up

the other end of the pin with the relative

hole in the right-hand support (4).

Using a screwdriver, push the pin into the

hole so that the groove (5) can be

reached. Fit the snap ring (6) into the

groove and hook on the right (7) and left

(8) springs, as shown.

1.2a Handle type "A" - without height

adjustment. Attach the lower part of the

handle (1) to the side supports on the

chassis. Secure it using the screws (2)

supplied, making sure that the

centring washers (3) are positioned

correctly. Attach the upper part (4) using

the screws (5) supplied, ensuring that the

spiral (6) of the starter cable is in the

correct position. Attach the control cables

using the clips (7).

1.2b Handle type "B" - with height

adjustment - Return the lower part of the

pre-fitted handle (1) to its working

position and lock into place using the

lower knobs (2). Attach the upper part (3)

using the screws (4) supplied, ensuring

that the spiral (5) of the starter cable is in

the correct position. Attach the control

cables using the clips (6). By loosening

the knobs (2) the handle can be set at

three different heights.

1.4a For a rigid grass-catcher, assemble

the two parts (1) and (2), making sure that

the hooks are fully clicked into position.

2. DESCRIPTION OF CONTROLS

2.1 The throttle (where fitted) is controlled

by the lever (1) and positioned as shown

on the relative plate. Some models have a

fixed speed, and therefore no need of a

throttle (2).

2.2 The blade brake is controlled by the

lever (1), which should be held against the

handle when

starting and using the lawnmower. The

engine stops when the lever is released.

2.3 In power-driven models, draw the

lever (1) towards the handle for forward

movement. The lawnmower stops moving

forward when the lever is released.

2.4 The cutting height is adjusted using

the levers (1). The four wheels must be at

the same height.

MAKE THIS ADJUSTMENT ONLY WHEN

THE BLADE HAS STOPPED MOVING.

3. GRASS CUTTING

3.1 Lift the stone-guard and attach the

rigid grasscatcher (1) or cloth grass-

catcher (2) correctly as shown in the

drawings.

3.2 To start the engine, follow the

instructions in the engine booklet and

then pull the blade brake lever (1) towards

the handle and give a sharp pull on the

starter cable knob (2). For models with an

electric starter, turn the starter key (3).

3.3 The lawn will look better if it is always

cut to the same height and in alternate

directions.

3.4 When you have finishing mowing,

release the brake lever (1) and disconnect

the spark plug cap (2). Remove the

starter key (3) (where fitted).

WAIT FOR THE BLADE TO STOP before

carrying out any type of work on the

machine.

HELPLINE UK NO. 0845 600 2912

WEB SUPPORT www.mowerfix.info

MODEL NUMBER: GL480 SP