Gardeline GL 480 SP Manuale di avvio rapido - Pagina 16
Sfoglia online o scarica il pdf Manuale di avvio rapido per Tagliaerba Gardeline GL 480 SP. Gardeline GL 480 SP 19.
Stampa la paginaOperator Manual
General assembly
information
If you have any problems
assembling or using this mower
please call our Helpline on:
0845 600 2912
For instructions regarding the engine
and the battery (if supplied), read the
relevant manuals.
NOTE – The machine can be supplied with
some of the components already fitted.
1. FINISH ASSEMBLY
1.1 To mount the stone-guard (1), the left
end of the pin (2) must be pushed
through and then inserted in the hole of
the left-hand (3) on the chassis. Line up
the other end of the pin with the relative
hole in the right-hand support (4).
Using a screwdriver, push the pin into the
hole so that the groove (5) can be
reached. Fit the snap ring (6) into the
groove and hook on the right (7) and left
(8) springs, as shown.
1.2a Handle type "A" - without height
adjustment. Attach the lower part of the
handle (1) to the side supports on the
chassis. Secure it using the screws (2)
supplied, making sure that the
centring washers (3) are positioned
correctly. Attach the upper part (4) using
the screws (5) supplied, ensuring that the
spiral (6) of the starter cable is in the
correct position. Attach the control cables
using the clips (7).
1.2b Handle type "B" - with height
adjustment - Return the lower part of the
pre-fitted handle (1) to its working
position and lock into place using the
lower knobs (2). Attach the upper part (3)
using the screws (4) supplied, ensuring
that the spiral (5) of the starter cable is in
the correct position. Attach the control
cables using the clips (6). By loosening
the knobs (2) the handle can be set at
three different heights.
16
1.4a For a rigid grass-catcher, assemble
the two parts (1) and (2), making sure that
the hooks are fully clicked into position.
2. DESCRIPTION OF CONTROLS
2.1 The throttle (where fitted) is controlled
by the lever (1) and positioned as shown
on the relative plate. Some models have a
fixed speed, and therefore no need of a
throttle (2).
2.2 The blade brake is controlled by the
lever (1), which should be held against the
handle when
starting and using the lawnmower. The
engine stops when the lever is released.
2.3 In power-driven models, draw the
lever (1) towards the handle for forward
movement. The lawnmower stops moving
forward when the lever is released.
2.4 The cutting height is adjusted using
the levers (1). The four wheels must be at
the same height.
MAKE THIS ADJUSTMENT ONLY WHEN
THE BLADE HAS STOPPED MOVING.
3. GRASS CUTTING
3.1 Lift the stone-guard and attach the
rigid grasscatcher (1) or cloth grass-
catcher (2) correctly as shown in the
drawings.
3.2 To start the engine, follow the
instructions in the engine booklet and
then pull the blade brake lever (1) towards
the handle and give a sharp pull on the
starter cable knob (2). For models with an
electric starter, turn the starter key (3).
3.3 The lawn will look better if it is always
cut to the same height and in alternate
directions.
3.4 When you have finishing mowing,
release the brake lever (1) and disconnect
the spark plug cap (2). Remove the
starter key (3) (where fitted).
WAIT FOR THE BLADE TO STOP before
carrying out any type of work on the
machine.
HELPLINE UK NO. 0845 600 2912
WEB SUPPORT www.mowerfix.info
MODEL NUMBER: GL480 SP
03