Jancy Engineering Slugger USA5 Panduan Operator - Halaman 7
Jelajahi secara online atau unduh pdf Panduan Operator untuk Bor Jancy Engineering Slugger USA5. Jancy Engineering Slugger USA5 16 halaman.
Halaman Cetak
- 1. Table of Contents
- 2. Important Safety Instructions
- 3. Special Instructions
- 4. Extension Cords
- 5. Grounding Instructions, Extension Cords, Guideline for Shift Lever Position
- 6. Contents of Package
- 7. Getting Started, before You Drill
- 8. Before the Cut, Ready to Cut, after the Cut
- 9. Basic Troubleshooting
- 10. Regular Maintenance
- 11. Control Panel and Parts List
- 12. Machine and Arbor Breakdown
- 13. Machine and Arbor Parts Lists
- 14. Motor Breakdown and Parts List
- 15. Dimensions and Specifications
Remove all contents from packaging and inspect to ensure no damage was incurred during shipping. Your USA5 package
should also include the following:
always disconnect
NOTE: The item numbers found below in parentheses refer to the images on page 12.
Assemble three spoke handles (item #18) to hub pinion shaft (item #17). NOTE: Feed hub assembly is mounted on
right side of machine frame . If necessary, it can be reversed for lefthand operation by simply removing the fastener (item
#29) and sleeve (item #30) from frame. Remove hub pinion shaft from right side of frame and insert it into left side of
frame. Replace sleeve and fastener into frame and tighten securely. Thread pipe handle (item #2) into motor housing.
The control panel (item #27) may also be reversed from left to right side of machine if desired. Remove screws (item
#19) holding control panel and side cover plate (item #20) next. Remove side cover plate and control panel, then
disconnect magnet and motor pin connections when removing control panel. Move control panel to opposite side of
frame. Reconnect magnet and motor pin connectors and secure control panel assembly using four screws (item #19).
Replace side cover plate, making sure warning instructions are visible.
what you should know before you drill
1. Type of material to be drilled, Brinnell or Rockwell hardness, material thickness and position should all be determined
to ensure proper selection of Slugger® cutting tools, RPM, coolant and drilling time.
2. Remove any excessive mill scale or rust from surface to be drilled.
3. When drilling materials under 3/8" thick, an additional steel plate may be required to achieve proper magnet
adhesion.
4. Material that has been flame cut may have become heat-treated and therefore difficult to drill. Avoid drilling near
such areas whenever possible.
5. Drilling with the USA5 in horizontal positions requires a special lubrication for Slugger® cutters.
Consult Jancy Engineering for details.
contents of package
description
OPERATOR'S MANUAL
PRODUCT DVD
WARRANTY CARD
3/16" PILOT, 1" DEPTH OF CUT
3/16" PILOT, 2" DEPTH OF CUT
1/4" PILOT, 1" DEPTH OF CUT
1/4" PILOT, 2" DEPTH OF CUT
1/4" PILOT, 3" DEPTH OF CUT
3/8-24 X 5/16" FPSSS
3/16" HEX WRENCH
3/16" T-HANDLE HEX WRENCH
4MM HEX WRENCH
SPOKE HANDLE
SAFETY STRAP
PIPE HANDLE
PIPE HANDLE ADAPTER
MAGNET WARNING NOTICE
SHUNT (ATTACHED TO HANDLE)
SHUNT INSTRUCTIONS
getting started
CAUTION!
usa5
from power source before making adjustments
#
part
qty
LIT104
1
LIT032
1
0070342
1
16001
1
16002
1
16003
1
16004
1
16005
1
UH1474
3
UH8013
1
UH8014
1
UH8002
1
0151333
3
U11005
1
0010224
1
0010225
1
0107D0C
1
UH5335
1
U14102
1
.
7