KitchenAid 30” Built-in Microwave Hood Panduan Petunjuk Instalasi - Halaman 7

Jelajahi secara online atau unduh pdf Panduan Petunjuk Instalasi untuk Oven Microwave KitchenAid 30” Built-in Microwave Hood. KitchenAid 30” Built-in Microwave Hood 8 halaman.

Halaman Cetak

If bollcm of upper cabinet Is recessed 3/4" or

more, align 2" x 2" filler Mocks (not included) with

Ihe shaded squares marked 'N" and 'P" on ihe

uwercabinel

lemolate. Mark the cuiout msition

onlhe filler blo&lhrough

Ihe uppercabir&l

holes 'L" and 'M". Drill 348" diameter hole al lhe

marks on filler blodts. Anach filler bkcks to upper

cabinet wilh the two 1/4*x 2' t&s and washers.

DO NOT TIGHTEN BOLTS AT THIS TIME.

1 -socild::~

lnslall power-supply cord bushing around

hole drllled In a metal cablnel. Failure to do

II .

lemplale. If

Cut oul or drill a 2" diameler hole

al Ihe area marked 'power-supply-

cord hole" on the upper-catinel

upper cabinel is melal, install power-

supplycord bushing around Ihe edge of hole lo

prevenl damage lo lhe cord from the rough metal

edge.

Delermine which venling method

(roof-venting, wall-venting. or

venlless) you need lo use. This microwave

oven is manufactured lor roof- or wall-venling

mslallalion. Some models can nol be mslalled

using lhe venlless (redrculaling) melhod

(12

To venI lhrough Ihe rool, WI oul

the rectangular area marked 'R"

on the upper catinel lemplale.

To vent through Ihe wall, cut out the rectangular

area marked 's" on Ihe wall lemplale.Remove lhe

upper-cabinet and wall templates.

Remove the upper-cabinet and wall lemplates.

1131

IllStall ductwork lhrough Ihe venl

opening in the upper-cabinet or

wall. Cor@ele Ihe venling system

through Ihe wall or rwf according lo Ihe method

needed. See Venting requiremenls and Venlirg

preparation. Use caulking lo seal edenor-wall or

rool opening around erhausl cap.

lcggls boll

mo"nllnp

p,m

/141

Inserl lag screws through the holes

on the mounting plate ('l-l") where

Ihe rnounlinq oiale will be aHached lo a wall stud:

inserl loggle-t&s

al 'D'. 'E", 'F. and 'G". where.

il will be anached lo dry wall.

-l--J-

AHach a spring toggled head lo Ihe end of each

loggle boll. Leave al leas1 one wall-lhickness of

space between Ihe mounting plate and the end

01 the spring toggle head so lhal Ihe spring toggle

head can properly open on Ihe olher side 01 the

wall.

)15j

If wall-vented inslallalion Is used,

ahach damper lo rear 01 mxmling

pble. Align 3.114 x lo' &cl wrlh damper and

see lhal damper moves Ireely.

Poslliin the mounting plate on the wall makina

sure lhal the lop 01 the mwrrling plate is 316;

below Ihe bollom of the c&r-&

Irame. InserI the

loggle bolls and spring toggle heads through the

dry-wall holes and start the lag screws through

the wall-stud holes.Tghlen tolls and screws lo

sewre mounlirg plale lo wall.

116

Inserl a ha&blade screwdriver

lhrough Iurn-rod clearance holes

in mounting @ale and inlo relainen. Move

screwdriver around lo make sure the retainers

move freely. II retainers do nol move Ire&y,

loosen toggle balls arrd lag screws, and readjusl

the nmnlirg

@ale.

Personal Injury Hazard

TWO people are required lo llfl lhls

mlcrowave.

Failure to use more than one

person during lnaiallallon may result In

personal Injury.

Careluliy III the microwave oven

' '

andi-mgilonlhshvolabssllhe

tollom of Ihe mounting plale.

Reaching lhrough upper cabinet, thread power

cord lhrwgh the power-cord hole in Ihe bonom 01

Ihe upper cabinel

(18

Swing Ihe microwave oven upward

so lhal lhe lop 01 Ihe oven meels

lhs 100 of lhe rmunling plate. Hc4d oven securely.

1191

Using a W-blade screwdriver, push

in and turn the turn-rod screws

' clockwise until they are tighl in rear,

mounling-plate nuts. Check that Ihe microwave is

securely faslened to the mounting plale.

Personal Injury or Property

Damage Hazard

Secure the mkrowave

oven wllh the two

mounllng bolts Inserted lhrwgh

the upper cablnel holes.

Fallure lo do ao could result In personal

Injury and/or propeny damage.

i7ghlen the bolIs inserled in lhe

upper cabinet holes until Ihe gap

between the upper cabinet and microwave oven

is closed.

Mwnl the power-supply cord

retainem as shown to lhe inside 01

the cabinet. Use power-supply-cord lie wraps lo

bundle Ihe Dower-suodv cord and seane ll lo

Ihe power&ppiy&i

ielainen

122

Reanach grille lo the front 01 Ihe

n%crowave oven with Ihe lhree

grille screws.

)23

Plug in Ihe power supply cord.

124

Read your Use 8 Care Guide then

check the cperalron 01 your

microwave oven.

To get the most efficient

use from

your new Microwave

Hood, read your

KitchenAid

Use and Care Guide.

Keep

Installation

Instructions

and Guide

close to oven for easy reference.

PANEI F