Garmin GHP Reactor Hydraulic Panduan Petunjuk Instalasi - Halaman 7
Jelajahi secara online atau unduh pdf Panduan Petunjuk Instalasi untuk Peralatan Kelautan Garmin GHP Reactor Hydraulic. Garmin GHP Reactor Hydraulic 15 halaman.
Halaman Cetak
2
In the location where you want to connect the helm control,
disconnect one side of a NMEA 2000 T-connector
network.
3
If necessary, connect a NMEA 2000 backbone extension
cable (not included) to the side of the disconnected T-
connector to extend the NMEA 2000 network backbone.
4
Add an included T‑connector for the helm control to the
NMEA 2000 backbone by connecting it to the side of the
disconnected T‑connector or backbone extension cable.
5
Route the included drop cable
the bottom of the T-connector added in step 4.
If the included drop cable is not long enough, you can use a
drop cable up to 6 m (20 ft.) long (not included).
6
Connect the drop cable to the helm control and the T-
connector.
7
Repeat steps 2 through 6 for the CCU.
Connecting Optional NMEA 2000 Devices to the
Autopilot System
You can use advanced features of the autopilot system by
connecting optional NMEA 2000 compatible devices, such as a
wind sensor, a water-speed sensor, or a GPS device to the
NMEA 2000 network.
NOTE: You can connect optional devices that are not NMEA
2000 compatible to the helm control through NMEA 0183
(NMEA 0183 Connection
Considerations).
1
Add an additional T-connector (not included) to the NMEA
2000 network.
2
Connect the optional NMEA 2000 device to the T-connector
by following the instructions provided with the device.
Configuring the Autopilot
The autopilot must be configured and tuned to your boat
dynamics. The Dockside Wizard and the Sea Trial Wizard on
the helm control are used to configure the autopilot. These
wizards walk you through the necessary configuration steps.
The Dockside Wizard
If you perform the Dockside Wizardwhile your boat is out of the
water, provide rudder-movement clearance to avoid damage to
the rudder or other objects.
You can complete the Dockside Wizard while the boat is in or
out of the water.
If the boat is in the water, it must be stationary while you
complete the wizard.
to the helm control and to
NOTICE
Performing the Dockside Wizard
If you have a boat with a power assist steering system, turn on
the power assist steering system before performing the
Dockside Wizard to avoid damaging the steering system.
1
Turn on the autopilot.
The first time you turn on the autopilot, you are prompted to
complete a short setup sequence.
2
If the Dockside Wizard does not start automatically after the
setup sequence, select Menu > Setup > Dealer Autopilot
Setup > Wizards > Dockside Wizard.
3
Select the vessel type.
4
Test the steering direction
5
If necessary, select the speed source
Source).
6
If necessary, verify the tachometer
Tachometer).
7
Review the results of the Dockside Wizard
Results of the Dockside
from the
Testing the Steering Direction
1
While moving at a low rate of speed, select
When you select
When you select
right.
2
Select Continue.
3
Select an option:
• If the steering test turns the boat in the correct direction,
select Yes.
• If the steering test turns the boat in the opposite direction,
select No and repeat steps 1 though 3.
Selecting the Speed Source
Select an option:
• If you connected a NMEA 2000 compatible engine (or
engines) to the NMEA 2000 network, select Tach. - NMEA
2000 or Proprietary.
• If NMEA 2000 tachometer data source is not available or
unusable, select GPS as a speed source.
• If you did not connect a NMEA 2000 tachometer or GPS
device as a speed source, select None.
NOTE: If the autopilot does not perform well using None
as the speed source, Garmin recommends connecting a
tachometer through the NMEA 2000 network or using a
GPS device as the speed source.
Verifying the Tachometer
This procedure does not appear when GPS or None is selected
as the speed source.
With the engine (or engines) running, compare the RPM
readings on the helm control with the tachometer (or
tachometers) on the dashboard of your boat.
If the RPM numbers do not align, there may be a problem
with the NMEA 2000 speed source or connection.
Reviewing the Results of the Dockside Wizard
The helm control displays the values you chose when you ran
the Dockside Wizard.
1
Examine the results of the Dockside Wizard.
2
Select any incorrect value, and select Select.
3
Correct the value.
4
Repeat steps 2–3 for all incorrect values.
5
When you are finished reviewing the values, select Done.
NOTICE
(Testing the Steering
(Selecting the Speed
(Verifying the
(Reviewing the
Wizard).
, the rudder must turn the boat to the left.
, the rudder must turn the boat to the
Direction).
and
.
7