Brother MFC490CW - Color Inkjet - All-in-One Manual Koneksi - Halaman 4

Jelajahi secara online atau unduh pdf Manual Koneksi untuk Perangkat lunak Brother MFC490CW - Color Inkjet - All-in-One. Brother MFC490CW - Color Inkjet - All-in-One 6 halaman. Mac network connection
Juga untuk Brother MFC490CW - Color Inkjet - All-in-One: Panduan Pengaturan Cepat (48 halaman), Panduan Pengaturan Cepat (47 halaman), Pengaturan & Pemasangan (5 halaman), Petunjuk Perbaikan (2 halaman)

Halaman Cetak

Brother MFC490CW - Color Inkjet - All-in-One Manual Koneksi

MFC490CW Vista Network Connection Repair Instructions

d. WPA/WPA2-PSK Encryption type (TKIP or AES) (If needed)

e. WPA/WPA2-PSK (Pre-shared Key) (If needed)

2. Verify the Wireless Router or Access Point is setup for DHCP. This setting is required in order for the

router or access point to broadcast a valid IP address to the device. Please refer to the user guide of

your wireless router or access point for additional information.

3. If the Brother machine was previously configured for wireless connection, continue to step 4 of this

section. If the machine was NOT configured for wireless connection, skip to step 5.

4. If the Brother machine was previously configured for wireless connection the network settings need to

be reset before the unit can be configured for new wireless settings. Complete the following steps to

reset the Network Card.

NOTE: Resetting the network card will erase all current network settings.

a. On your machine, press MENU.

b. Scroll to NETWORK and press OK.

Scroll to FACTORY RESET and press OK.

d. Press 1 twice for YES to accept the change.

5. When the machine powers on:

a. Press MENU

b. Scroll up or down to NETWORK and press OK.

Scroll up or down to WLAN and press OK.

d. Scroll up or down to SETUP WIZARD and press OK.

e. When NETWORK I/F SWITCHED TO WIRELESS is displayed, press OK.

6. The machine will search for your network and display a list of available SSIDs. You should see the

SSID you wrote down earlier. If the machine finds more than one network use the up or down arrow

keys to choose your network, then press OK, and then skip to step 10 of this section. If your access

point is set to not broadcast the SSID you will have to manually add the SSID name.

7. Select <NEW SSID> using up or down arrow and press OK.

8. Enter a new SSID using the keypad then press OK. The SSID must match the settings of your router

or access point. You can use the left and right arrow keys to move the cursor left and right. For

example, to enter the letter a, press the 2 key on the dial pad once. To enter the number 3, press the

3 key on the dial pad seven times. The letters appear in this order: lower case, upper case and then

numbers. Press OK once all the letters have been entered.

9. Press up or down arrow to choose INFRASTRUCTURE, and then press OK.

10. Use the up or down arrow, and OK keys to choose one of the options below: If your network is

configured for Authentication and Encryption you must match the settings used for your network.

a. NO AUTHENTICATION OR ENCRYPTION: Scroll to OPEN SYSTEM, and press OK. Scroll to NONE

for Encryption Type and press OK. Press 1 (YES) to apply your settings. Skip to step 13.

b. NO AUTHENTICATION WITH WEP ENCRYPTION: Scroll to OPEN SYSTEM, and press OK. Scroll

to WEP for the Encryption Type and press OK. Continue to step 11.

AUTHENTICATION WITH WEP ENCRYPTION: Scroll to SHARED KEY, and press OK. Continue to

step 11.

d. AUTHENTICATION WITH WPA/WPA2-PSK (TKIP or AES) ENCRYPTION: Scroll to WPA/WPA2-

PSK, press OK. Skip to step 12.