Bil-Jax 4527A Informasi Operasional dan Keselamatan - Halaman 4
Jelajahi secara online atau unduh pdf Informasi Operasional dan Keselamatan untuk Lift Boom Bil-Jax 4527A. Bil-Jax 4527A 13 halaman. Articulate boom lift
Halaman Cetak
F. USAGE RESPONSIBILITIES;
MACHINE INSPECTION; continued ...
6. Hydraulic Leaks; This is best done by walking around the machine. Do not expose yourself to any potential
shear or pinch points. Check the hydraulic hose and fittings for leaks and damages daily. Always use
care when visual inspecting for hydraulic fluid. Hydraulic fluid under pressure can penetrate the skin or
eyes and cause serious injury. Always wear a face shield or safety goggles for eye protection whenever
you are operating or "visually" inspecting the machine. Always wear gloves but avoid touching hydraulic
fluids. Use cardboard to confirm hydraulic fluids on machinery. Dispose of cardboard in a responsible
manner. If any fluid is injected into the skin, it must be removed within a few hours by a doctor familiar
with this type injury. Do not operate this equipment if; damages occurs, leaks appear or if there are
any operational abnormalities or any controls malfunctioning. Stop immediately and contact TRC at
(662) 335-3535, (662) 822-1907 or (662) 822-1909.
(see the Manufacturer's "Operator's Manual", pages; 1-4 and 1-5).
WORK SAFETY;
This machine is not insulated for use near electrical power lines and "
ELECTRICAL;
protection from contact with or close proximity to any electrically charged conductor. Operator must maintain
safe clearance at all times (10 feet minimum) and always allow for platform movement such as wind induced
sway.
WARNING;
should always be at least 50' from electrical pylons and 30' from cables on wooden poles. These
recommended safe distances meet or exceed those specified in ANSI standards and OSHA
requirements. Boom lifts are one of the safest ways of doing temporary work at heights, so the
burden is on "the operators" to stay safe near power lines and conductors are any other energized
source, etc. Electrocutions can be prevented thru proper planning, risk assessment and
management of work at height, including operator training and familiarization. Assume "
POWER LINE
machine contacts energized power lines,
IF
Minimum Safe Approach Distances; (Consult the Manufacturer's "Operator's Manual", pages; 1-4).
Voltage Range
(Phase to Phase)
0 to 300 V ............................
Over 300V to 50KV ....................
Over 50KV to 200KV ..................
Over 200KV to 350KV ................
Over 350KV to 500KV ................
Over 500KV to 750KV ................
Over 750KV to 1000KV ..............
Always position the lift far enough away from a power source to ensure that no part of the lift can accidently
reach into an unsafe area. This includes full extension of the boom through 360 degrees rotation.
OPERATIONAL USE;
prohibited. Stay clear of wires, cables, eves and other overhead obstructions. Make personnel aware and
keep them away from potential pinch points, shear points and from potential crush hazards as indicated by
machine decals attached to the machine. Keep the safety bar lowered at all times unless personnel are entering
or exiting the work platform. Always keep personnel and obstructions clear of the machine when repositioning
or operating the boom and basket. Cordon off the work area surrounding the outriggers to keep personnel,
vehicles and moving equipment away from the machine. Always exercise caution when rotating the boom
(slew) from the ground control station. Watch for personnel inside the radius of the turret and boom arm when
rotating the boom lift from the ground or platform controls. Keep a wide stance to help maintain sure footing
on the work platform. Keep the platform and all work areas free of debris.
WARNING;
welding is being performed from the platform. Never use the machine as a ground for welding.
Never use without the outriggers fully extended, locked and firmly based. When on soft surfaces, always use
outrigger base plates. Never operate on a slope exceeding 12.5 degrees. Never override or by-pass the
manufacturer's safety devices. Never attach a safety harness to an adjacent structure, pole or equipment while
working from the boom lift. Never release the outrigger locks or move with a person or materials on board.
Never release the outriggers or move the trailer with the boom extended. Never stand or sit on cage bars. Work
only within the work cage and do not lean out over the cage to perform work. The operator shall not use railings,
planks, ladders or any other devices in or on the work platform for achieving additional working height or reach.
Never allow ropes, electrical cords, hoses, etc., to become entangled in the equipment, especially when the
basket is being raised or lowered. Always make sure all tools and equipment are safely stowed. Do not exceed
load ratings by transferring loads to the basket at elevated heights. Never use cage to carry materials and never
allow overhang of materials when raising or lowering the basket. Never push or pull with the boom or basket
and never use the boom to lift any part of the trailer. Never use the boom or basket to place a "dead man" load
(to prop up other items) against any structure, materials or equipment. Never climb up or down a down boom.
Never leave the keys in the boom lift while unattended or not in use. Never leave an elevated platform unattended.
2015 - BIL-JAX #4725A, "TOWABLE - ARTICULATE BOOM LIFT" - OPERATIONAL & SAFETY INFO
The IPAF (International Powered Access Federation) states that an extended boom lift
" is live. Always contact the power company before performing work near power lines.
Always report any misuse of the equipment to the proper authorities. Horseplay is
"Welding Information" ... Never allow electrode contact with any part of the basket if
touch or operate until power lines are shut off.
NEVER
Minimum Safe Approach Distances
(Feet)
(Meters)
Avoid Contact
10'
15'
20'
25'
35'
45'
13.72
DOES NOT"
provide
EVERY
3.05
4.60
6.10
7.62
10.67
...
page 4 - 12