Avtron AV115 Petunjuk Manual

Jelajahi secara online atau unduh pdf Petunjuk Manual untuk Konverter Media Avtron AV115. Avtron AV115 10 halaman.

Halaman Cetak

8 9 0 1 E . P L E A S A N T VA L L E Y R O A D

I N D E P E N D E N C E , O H I O 4 4 1 3 1 - 5 5 0 8

T E L E P H O N E : ( 1 ) 2 1 6 - 6 4 2 - 1 2 3 0 • FA X : ( 1 ) 2 1 6 - 6 4 2 - 6 0 3 7

E - M A I L : t a c h s @ a v t r o n . c o m • W E B : w w w. a v t r o n e n c o d e r s . c o m

DESCRIPTION

The Avtron AV115 is a modular, two piece incremental encoder

(also known as a tachometer or rotary pulse generator). It provides

a two phase, A Quad B frequency (pulse) output, with comple-

ments. The AV115 mounts on a 115mm C-Face, also known as

a B-Flange.

Because the AV115 is modular, there are no bearings or

couplings required. This, combined with the latest magneto-

resistive (MR) sensor technology, allows the AV115 to

provide superior mechanical performance and increased reliability.

An Avtron AV115 can be configured with one or two independent

outputs. Each output has six signals: (A, B) 90° out of phase, with

–

complements (A

, B

). A marker pulse with complement (Z, Z

also provided.

Output resolution on the AV115 is determined by the sensor only.

Unlike older models, any PPRs can be mixed and matched.

Selection of the rotor is based only on the shaft mounting require-

ments (and not PPR).

Special option 002 selects an alternate PPR code

defini tion. Example: A-128 PPR with option code

000. A*-1270 PPR with option code 002.

INSTALLATIONs

Refer to the back page of these instructions for outline and

mounting dimensions. Axial float or endplay must be less than

±1.27mm.

In preparation for installing the Model AV115 pulse generator, it is

first necessary to clean both the accessory motor shaft and the

mounting face. These surfaces must be inspected and any paint,

burrs, or other surface imperfections removed.

AV115 PART NUMBERS AND AVAILABLE OPTIONS

Model Housing Type

(Thru Shaft Rotor)

AV115

1- Single Output

C0- Non. Std. Shaft Size

XX- None

2- Dual Output

Thru Shaft Rotor (Metric)

D2- 10mm

DA- 11mm

D3- 12mm

DB- 14mm

DC- 15mm

DD- 16mm

Cam Screw Rotor only

D4- 18mm

10mm-60mm

DE- 19mm

DF- 24mm

^ To specify this PPR,

DG- 28mm

also specify modifica

DH- 30mm

tion code 002

DT- 32mm

DJ- 36mm

INDUSTRIAL AUTOMATION, INC.

NOTE

Shaft Size

Cover Style Line Driver

E- Extended

Shaft Cover

F- Flat Cover

DK- 38mm

T- Flat Thru-

DL- 42mm

Hole Cover with

DM- 45mm

Shaft Seal (Seal

DN- 48mm

DP- 52mm

not available

DR- 55mm

on shafts larger

DS- 60mm

than 75mm)

MU- 65mm*

MV- 70mm*

MW- 75mm*

MY- 80mm*

MZ- 85mm*

Equipment Needed for Installation

Provided

AV115 Stator/Housing

Socket Hd Cap Screw

M10 x 20mm (4)

AV115 Rotor

Socket Set Screw

M4 x 6mm (2) or Pre-

installed cam screw

Thread locker (blue)

–

Installation procedures should be performed only by qualified

) is

personnel. Safety precautions must be taken to ensure machin-

ery cannot rotate and all sources of power are removed during

installation.

ROTOR INSTALLATION

The motor shaft must project at least 16mm from the motor

face. For set screw rotors only: Apply anti-seize compound to

the motor shaft. For all rotors: Slide the rotor onto the shaft with

the marking "This side out" facing out (away from the motor

face). The rotor centerline must match the sensor centerline. To

accomplish this, use the rotor locating gauge (A28503) and slide

the rotor onto the shaft until it is in the proper position as shown

in Figure 1. If a guage is not available, use the stator housing

alignment grooves as show in Figure 3.

STANDARD CAM SCREW ROTOR INSTALLATION

Turn the cam screws of the rotor in the directions shown on the

rotor to engage the cams. Tighten to 5.6 - 6.8 N-m (See Figure2)

using the 3mm hex wrench. Total cam screw rotation will be less

than one turn.

Single/Left

Right Output

Output (PPR)

6- 5-24V in/out

C^- 50

0- Non.

R- 512

F- 60

Std.

S- 600

8- 5-24 V in,

G- 100

C^- 50

V- 900

5-15 V out

H- 120

F- 60

J- 960

high power

A- 128

G- 100

Y- 1024

9- 5-24V in,

B^- 150

H- 120

Z- 1200

5V out

L- 240

A- 128

A^- 1270

N- 256

B^- 150

3- 2000

P- 300

L- 240

4- 2048

N- 256

5- 2500

E- 360

P- 300

D- 4096

B- 480

E- 360

8- 4800

R- 512

S- 600

B- 480

9- 5000

V- 900

Q- 500

Encoder

Instructions

MODEL

AV115

115mm FLANGE MOUNT

MODULAR

Optional

Extended Shaft

Phillips Screwdriver

Cover w/ Screws

2mm Hex Wrench

6-32 x 0.31" (4)

Lock Washers

Shaft Rotors >70mm)

Thru Shaft Cover

3mm Hex Wrench

w/ V-Ring Seal and

8mm Hex Wrench

Silicone Lubricant

Connector

(PPR)

P- 10 Pin EPIC Industrial

J- 960

Y- 1024

w/ Plug

Z- 1200

G- 10 Pin Industrial w/ Plug

A^- 1270

(Northstar pinout)

3- 2000

W- 3 Ft. Cable, Sealed

4- 2048

5- 2500

Z- 3 Ft. Cable w/ EPIC

D- 4096

Industrial

8- 4800

9- 5000

0- Non-

Std.

X- None

Not Provided

(T-Handle Style for Thru-

Modifications

000- No Modification

002

-select alternate PPR

assign ment code

004- Add Housing Drain

(single output only)

9xx- Special Cable Length,

xx=length in feet