Miller 028042103 Panduan Pemilik - Halaman 5

Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Sistem Pengelasan Miller 028042103. Miller 028042103 20 halaman.
Juga untuk Miller 028042103: Panduan Pemilik (20 halaman), Panduan Pemilik (20 halaman), Panduan Pemilik (20 halaman)

Halaman Cetak

SECTION 1 – SAFETY PRECAUTIONS – READ BEFORE USING

Protect yourself and others from injury—read, follow, and save these important safety precautions and operating instructions.

1-1.

Symbol Usage

DANGER! – Indicates a hazardous situation which, if not

avoided, will result in death or serious injury. The possible

hazards are shown in the adjoining symbols or explained

in the text.

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury. The possible haz-

ards are shown in the adjoining symbols or explained in

the text.

NOTICE – Indicates statements not related to personal injury.

�

Indicates special instructions.

1-2.

Cooling Equipment Hazards

The symbols shown below are used throughout this manual

to call attention to and identify possible hazards. When you

see the symbol, watch out, and follow the related instruc-

tions to avoid the hazard. The safety information given be-

low is only a summary of the more complete safety

information found in the Principal Safety Standards listed in

Section 1-5. Read and follow all Safety Standards.

Only qualified persons should install, operate, maintain,

and repair this equipment. A qualified person is defined as

one who, by possession of a recognized degree, certificate,

or professional standing, or who by extensive knowledge,

training and experience, has successfully demonstrated the

ability to solve or resolve problems relating to the subject

matter, the work, or the project and has received safety

training to recognize and avoid the hazards involved.

During operation, keep everybody, especially children,

away.

HOT PARTS can burn.

� Do not touch hot parts bare handed.

� Allow cooling period before working on equipment.

� To handle hot parts, use proper tools and/or wear

heavy, insulated welding gloves and clothing to

prevent burns.

FLYING METAL OR DIRT can injure

eyes.

� Wear approved safety glasses with side shields

even under your welding helmet.

1-3.

Additional Hazards For Installation, Operation, And Maintenance

FALLING EQUIPMENT can injure.

� Use correct procedures and equipment of ad-

equate capacity to lift and support unit.

� If using lift forks to move unit, be sure forks are

long enough to extend beyond opposite side of

unit.

� Keep equipment (cables and cords) away from moving vehicles

when working from an aerial location.

� Follow the guidelines in the Applications Manual for the Revised

NIOSH Lifting Equation (Publication No. 94-110) when manually

lifting heavy parts or equipment.

This group of symbols means Warning! Watch Out! ELECTRIC

SHOCK, MOVING PARTS, and HOT PARTS hazards. Consult

symbols and related instructions below for necessary actions to

avoid these hazards.

ELECTRIC SHOCK can kill.

Touching live electrical parts can cause fatal

shocks or severe burns. The input power circuit

and machine internal circuits are also live when

power is on. Incorrectly installed or improperly

grounded equipment is a hazard.

� Do not touch live electrical parts.

� Disconnect input power or stop engine before installing or servic-

ing this equipment. Lockout/tagout input power according to

OSHA 29 CFR 1910.147 (see Safety Standards).

� Properly install, ground, and operate this equipment according to

its Owner's Manual and national, state, and local codes.

� Always verify the supply ground - check and be sure that input

power cord ground wire is properly connected to ground terminal

in disconnect box or that cord plug is connected to a properly

grounded receptacle outlet.

� Keep cords dry, free of oil and grease, and protected from hot met-

al and sparks.

� Frequently inspect input power cord and ground conductor for

damage or bare wiring – replace immediately if damaged – bare

wiring can kill.

� Turn off all equipment when not in use.

� Use only well-maintained equipment. Repair or replace damaged

parts at once. Maintain unit according to manual.

� Keep all panels and covers securely in place.

OVERUSE can cause

OVERHEATING.

� Allow cooling period; follow rated duty cycle.

� Do not block or filter airflow to unit.

READ INSTRUCTIONS.

� Read and follow all labels and the Owner's Manual

carefully before installing, operating, or servicing

unit. Read the safety information at the beginning

of the manual and in each section.

� Use only genuine replacement parts from the manufacturer.

� Perform installation, maintenance, and service according to the

Owner's Manuals, industry standards, and national, state, and lo-

cal codes.

OM-254203 Page 1