AquaPRO WIP100PRO Petunjuk Pengoperasian dan Manual Suku Cadang - Halaman 2

Jelajahi secara online atau unduh pdf Petunjuk Pengoperasian dan Manual Suku Cadang untuk Pompa Kolam Renang AquaPRO WIP100PRO. AquaPRO WIP100PRO 8 halaman. Aquapro systems pool pump operating instructions and parts manual

Halaman Cetak

Operating Instructions and Parts Manual

Installation

When motor installation is within 5 ft.

(Continued)

(1.5 m) of the pool's interior walls, a

NOTE: Use an adhesive primer to

solid copper bonding conductor (mini-

ensure adhesive joints are secure.

mum size No. 8 AWG/8.4 mm

Suregard P-3000 has a purple tracer to

be connected from the accessible wire

qualify in areas where codes specify a

connector on the motor.

primer must be used.

• to all metal parts of the swimming

Consider climatic conditions when

pool

applying adhesives. Atmospheric condi-

• to all electrical equipment

tions with high humidity will make the

• to metal conduit

adhesive action of certain glues less

effective. Follow the manufacturer's

• to metal piping within 5 ft. (1.5 m)

instructions.

of the pool's interior walls

THREADED CONNECTIONS

IMPORTANT: Use copper

Use only Teflon

tape or equivalent on

conductors only.

threaded plumbing connections. Other

Refer to information on motor name-

pipe compounds may damage threads.

plate for electrical service data. Install

Do not use silicone or petroleum based

motors with a fused disconnect switch

compounds. Do not overtighten. Hand

or dedicated circuit breaker. Be sure

tightening plus 1/2 turn is sufficient.

wire size is sufficient for pump HP and

PUMP PLUMBING

distance from power source. Install a

ground fault circuit interrupter for

Suction pipe should be as large or larger

maximum safety.

than discharge pipe. Avoid using a suc-

tion pipe smaller than pump connection.

DANGER

1. Keep the piping as straight and

short as possible, and of suitable

source before attempting to install, ser-

size.

vice, relocate, or perform any mainte-

2. Do not connect an elbow directly

nance.

into the pump inlet. A length of

VOLTAGE SELECTOR

straight pipe will allow proper entry

This pump is factory wired for 230 volts.

of the water to the pump.

To change the voltage to 115 volts fol-

3. Slope horizontal runs upward to the

low the steps below:

pump to prevent trapping air.

1. Disconnect the pump from power.

4. Use independent piping supports to

2. Remove cover from back of motor

alleviate strain on the pump.

to find voltage selector (Figure 1a).

5. Keep as much of the suction line as

possible below the water level to

reduce priming time.

6. Install valves and unions in the

pump suction and return lines to

facilitate servicing. Valves will throt-

tle the pump discharge. Valves are

also essential for pump mainte-

nance if the system is installed

below deck level.

7. Use a check valve in the suction pipe

for inground pumps at or below the

water level if the suction lift is more

than 5 feet or the dry suction is

more than 10 feet long. Keep the

valve in the suction line fully open

during operation.

WIRING

WARNING

All

Figure 1a

wiring must be performed

by a qualified electrician.

The pump must be installed

3. Pull selector knob out.

in compliance with all local codes and

4. Rotate selector knob to correct volt-

the National Electrical Code.

age setting (Figure 1b).

115 Volts

) should

HI HI

Volt

Figure 1b

5. Push selector knob back in place.

6. Reinstall cover to back of motor.

Operation

Prime pump before attempting to oper-

ate. To prime pumps located above water

level, remove strainer cover, fill strainer

body with water then replace cover. If

pump and all piping is located below

water level, the pump will self prime.

After pump has been primed, open all

Disconnect, tag,

suction and discharge line valves and

and lock out power

energize motor. If no flow is observed

in five minutes, stop the motor and

reprime. If the pump fails to operate,

check for air leaks. Refer to trou-

bleshooting section.

After about 10 minutes of operation,

check the return fittings for air bubbles.

A continuous flow of air indicates leaks

in the suction line. Locate and correct

any leaks immediately.

CONTROLLING PUMP DISCHARGE

Keep the gate valve in the suction line

fully open during operation. To control

the discharge, use a valve in the return

line.

Do not retighten lid

CAUTION

during operation.

Do not operate

CAUTION

pump with closed

suction or discharge valve.

WATER CHEMISTRY

Proper and consistent use of chemicals

is necessary to manage a water system.

Chlorine is the most commonly used

chemical to provide clean, sanitary

Volt

water. Daily administration of dry or

liquid chlorine (calcium or sodium

hypochlorite) is essential.

IMPORTANT: Maintain the correct

level of acidity or alkalinity of the pool

water. Readings above pH 7.0 are alka-

line. A pH 7.0 is neutral. Readings

below pH 7.0 are acidic. A desirable

range is 7.2 to 7.4.

Manual de Instrucciones de Operación y Piezas

Para Piezas de Repuestos, Llame al 1-877-278-2797

230 Volts

HI HI

Volt

Notas

No. de

Ref.

Descripción

Juego de la bomba

Juego del sello del eje

Juego del motor

Tapa del cuerpo

de la bomba

Cesta filtrante

(no se muestra)

15 Sp

Envíe su solicitud de repuestos a la siguiente direccion:

AquaPro Systems

101 Production Drive

Harrison, OH 45030 U.S.A.

Sírvase proporcionar la suguiente información:

- Número de modelo

- Número de serie (si tiene)

- Descripción y número de repuesto como se muestra

en la lista de repuestos

WIP100PRO

WIP150PRO

Ctd.

69004-001

69005-001

21009-001

69000-001

69001-001

28563-001

28564-001

28565-001

28566-001