HP Xw460c - ProLiant - Blade Workstation Panduan Pertanyaan yang Sering Diajukan - Halaman 2

Jelajahi secara online atau unduh pdf Panduan Pertanyaan yang Sering Diajukan untuk Beralih HP Xw460c - ProLiant - Blade Workstation. HP Xw460c - ProLiant - Blade Workstation 14 halaman. Mezzanine card installation instructions for supported hp proliant c-class bladesystem servers
Juga untuk HP Xw460c - ProLiant - Blade Workstation: Panduan Pelaksanaan (35 halaman), Panduan Pencegahan Kesalahan (12 halaman), Buku Putih Teknis (12 halaman), Pembaruan Firmware (9 halaman), Panduan Instalasi (2 halaman), Poster Pengaturan (9 halaman), Panduan Instalasi (33 halaman), Panduan Manajemen (28 halaman), Manual Perangkat Keras (23 halaman), Ikhtisar (35 halaman), Panduan Pengguna (33 halaman), Panduan Pengoptimalan (13 halaman), Garansi Terbatas (10 halaman), Panduan Petunjuk Instalasi (10 halaman), Panduan Petunjuk Instalasi (8 halaman), Petunjuk Instalasi (4 halaman), Petunjuk Instalasi (2 halaman)

ISS Technology Update

Graphics traffic to remote workstations

The question has been asked, how is graphics data transmitted from the HP ProLiant xw460 Blade Workstation to remote

workstations? Users may assume that since it is in a mezzanine slot, the graphics data goes to interconnect bays 3 and 4.

However, there is no connection between the graphics mezzanine card and the interconnect slots; all output of the graphics

card is captured by Remote Graphics Software (RGS) and sent over the network. The integrated NICs are routed to interconnect

bays 1 and 2, the same as with the BL460c and BL465c half-height server blades.

Graphics output also depends on the remote console mode:

• Setup mode — Both the NVIDIA controller and embedded ATI controller are enabled, but the ATI is primary. In this mode,

graphical console redirection through the iLO is possible.

NOTE

On initial boot, one must access BIOS under system options to set the remote console to

Setup mode. To do so, reboot, press F9 into BIOS, and then select System Settings -> Remote

Console Mode -> Setup.

• Admin mode — Only the ATI controller is enabled, and the NVIDIA is disabled. In this mode, graphical console redirection

through iLO is possible.

• User mode (normal use) — The NVIDIA controller is enabled and the embedded ATI controller is disabled. In this mode,

graphical console redirection through iLO is NOT possible. A blinking cursor at the left top corner is the only thing visible

from the system console and iLO console redirection is rendered unavailable due to a dependence on the ATI controller.

At this point, the Workstation blade needs to be connected with an RGS receiver through the network. The graphics content is

compressed and sent to the receiver over this network connection. One receiver can connect to multiple senders, or one

sender can send to many receivers for session sharing.

Mixed configuration

The most common configuration question is this: can the HP ProLiant xw460 Blade Workstation be implemented with other

devices (such as an InfiniBand or Fibre channel device in mezzanine 2)? The Workstation blade is designed for both flexibility

and compatibility; it will work in harmony with all other HP BladeSystem products. Furthermore, Workstation blades, server

blade, and storage blades can be housed in the same chassis without impacting operability of the server or storage blade.

NOTE

At this time, the Workstation blade does not support the entire ProLiant BladeSystem family.

Further testing is required.

Future plans

There are future plans for the HP ProLiant xw460c Blade Workstation to support SB40c, PCI blades, tape blades, and shared

storage blades. With the release of RGS 5.0, support of Insight Control Environment for BladeSystems has been added to the

Blade Workstation's capabilities.

Volume 6, Number 9