BIOMICROBICS BioBarrier 1.0 Panduan Instalasi - Halaman 3

Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Sistem Air BIOMICROBICS BioBarrier 1.0. BIOMICROBICS BioBarrier 1.0 13 halaman. For use with nsf/ansi std. 40 class i/std. 350 class r, ansi/nsf std. 245
Juga untuk BIOMICROBICS BioBarrier 1.0: Panduan Pemilik (7 halaman)

Halaman Cetak

If nitrogen removal is needed the system (The BioBarrier

tanks totaling at least three compartments, with exactly two compartments in the second or final tank. The first compartment or

tank provides primary treatment - sedimentation and separation of floatables and solids, and is equipped with an outlet screening

device called SaniTEE

. The second and third compartments must be in the same tank, and the second compartment is where

denitrification takes place under anoxic conditions. The third compartment, the aeration/membrane zone, is separated from the

anoxic zone by a baffle wall between the two zones to allow nitrified waste to enter into the anoxic area for denitrification.

NSF Standard 350 Class R

The BioBarrier

system has been tested under NSF Standard 350 Class R (Residential) and is capable of treating residential

wastewater for restricted indoor urban water reuse, which is toilet and urinal flushing. The system design requires a holding tank

and plumbing system for reuse water and shall meet all applicable codes; have proper backflow prevention and protection against

cross connections; and is the responsibility of the local designer/installer. When the reuse water is used for toilet and urinal

flushing, additional disinfection should be considered to provide adequate assurance in preventing microorganism growth in the

treated reuse water storage tank and as required by applicable codes.

The reuse tank shall be located after the BioBarrier

water to be dispersed in a locally approved soil dispersal system or released into a sanitary sewer system. A potable water make

up system shall also be available to supply water when treated reuse water is not available. This potable water make up system

shall include a properly designed backflow preventer that meets all applicable codes.

NSF Standard 350 Class R

The BioBarrier® system has been tested under NSF Standard 350 Class R (Residential) and is capable of treating residential

wastewater for unrestricted outdoor urban water reuse, which is acceptable for use in surface and subsurface irrigation, including

irrigation of edible crops without the edible portion being in direct contact with the treated water. A reuse tank may be required if

the irrigation system requires it. The holding tank and plumbing system for reuse water shall meet all applicable codes; have

proper backflow prevention and protection against cross connections; and is the responsibility of the local designer/installer.

Additional disinfection should be considered to provide adequate disinfection to prevent microorganism growth in the treated

reuse water storage tank and as required by applicable codes.

If a reuse tank is required for irrigation, it shall be located after the BioBarrier® system. This tank shall also incorporate an overflow

that allows excess reuse water to be dispersed in a locally approved soil dispersal system or released into a sanitary sewer

system. If a potable water make up system is required for irrigation, it shall include a properly designed backflow preventer that

meets all applicable codes.

INSTALLATION PROCEDURE

Always have all utility lines and equipment marked by a locating service prior to performing any work. Failure to do so

could result in severe bodily injury or death.

Hazards exist in confined spaces such as a septic tank. All confined space precautions must be followed if entering a

tank. Always keep tank openings covered during storage and installation

MATERIALS REQUIRED FOR INSTALLATION

A. Septic tank that meets all applicable requirements and standards.

Recognized, safe lifting mechanism for treatment module (e.g. a tripod).

C. Non-corrosive strut channel or equivalent material that is able to hold down at least 550 pounds [250 kg] of

buoyant force (see step 29).

D. Stainless steel anchor bolts to secure strut channel to tank riser and blower housing to concrete base.

Piping for all air and vent lines. Check the install procedure all specs, and plans to determine what sizes

and types of pipe you may need.

PVC saw

G. Pipe joint lubricant/soap.

H. PVC primer and glue.

Concrete base for blower assembly.

Mounting screws for control panel.

Electrical conduit, fittings and wire for required wiring.

Hammer Drill and concrete bits.

0.5-N, 1.0-N, 1.5-N) consists of a tank with three compartments, or two

Restricted Indoor Urban Reuse Water

system. This tank shall also incorporate an overflow that allows excess reuse

Unrestricted Outdoor Urban Reuse Water