Accusplit A925MXTBL Petunjuk Pengoperasian

Jelajahi secara online atau unduh pdf Petunjuk Pengoperasian untuk Menonton Accusplit A925MXTBL. Accusplit A925MXTBL 2 halaman. Wrist-worn stopwatch with split memory

Halaman Cetak

ACCUSPLIT A925MXTBL

Wrist-Worn Stopwatch with Split Memory

Congratulations on your purchase of an A925MXTBL stopwatch

for the wrist! You're about to enjoy the convenience of having

professional timing right at your fingertips when you need it,

plus a regular wristwatch whenever you don't.

SETUP

Most watches ship with a battery inter-

rupt in place to save battery life. Turn the

watch over and use a quarter or nickle

to twist open the battery compartment

hatch. Remove clear plastic strip from

underneath the battery. Replace the bat-

tery, taking care to ensure that the posi-

tive (+) terminal is facing up. Replace the

battery compartment hatch and tighten

with the coin, making sure that the small

arrow points to the dot at the top of the

watch case when you are finished. Peel

the simulated display sticker off the

watch face.

Your new watch has four modes of op-

eration: 1/100th second Memory Stop-

watch with Turbo features, Triple-mode

Timer, plus two Time-of-Day/Date/Alarm

modes. When the battery is enabled,

your watch will come to life in stopwatch

mode. Press the

button to cycle be-

tween the modes. Your watch also has an

Electroluminescent backlight. Press the

EL button to activate the backlight.

STOPWATCH MODE

The watch features a professional timing

circuit with powerful stopwatch features.

This is how the display looks when in

stopwatch mode.

Split Counter

SPLIT

0 : 32 : 29

0 : 05 : 03

1 1

Split Time

E L

Master Reset

925MX

TURBO

Its a good idea to reset the stopwatch

each time before use. Push S2 for

2 seconds to Reset**

Event Timing

Event timing is the simplest form of tim-

ing. It is good when you want to mea-

sure the total time from the start to the

finish of a particular event.

S2 – Start

S2 – Stop (Display shows "SPLIT")

S2 (2sec) – Reset**

ACCUSPLIT, Inc. • 6120 Stoneridge Mall Rd., Suite 210 • Pleasanton, CA 94588 USA

800-965-2008 • 925-226-0888 • FAX 925-463-0147 • www.ACCUSPLIT.com • [email protected]

Operating Instructions

Dual Split Memory with Split

Counter

When timing an activity with pauses

or repeated events, you will need to

use split timing with memories.

S2 – Start (Shows Running DUAL Time)

S2 – Split* (Top shows CUM 1, Bottom

shows LAP 1)

S2 – Split* (shows CUM 2, Bottom shows

LAP 2)

S2 – Split* (Top shows CUM 3, Bottom

shows LAP 3)

S2 – Split* (Top shows CUM 4, Bottom

shows LAP 4)

S2 (2sec) – Reset**

*Split Counter always shows Current Split

Note: You can always press S1/S4 to return

to Running Time.

Memory Review (before Resetting)

M – Review* (Bottom shows AVE LAP

Split, Top shows TOTAL ELAPSED TIME)

M – Review (Shows last DUAL Split)

M – Review (Shows next DUAL Split, in

reverse order)

*Reviews at any time in reverse numerical

order. Hold down for Rapid Review.

STOPWATCH AND SPEED/RATE

The advanced "Turbo" functions on

the watch calculate speed or rate once

distance has been input into the watch

(recall that Rate = Units/Time).

Turbo

Set up

Display

Lap Time

Speed/Rate Function Setting

S1(2sec) - Enter Turbo (Speed/Rate) Set

Function

S1(4sec) – Enter set function and Reset

Turbo fields to zero (as for DUAL

SPLIT timing)

S2 – Select field to be Set (field will

flash)

S3 – Set field to Desired Setting

S4 – Exit Setting Function

S1/S4

SPLIT

0 : 32 : 29

0 : 05 : 03

E L

EL Backlight

Button

925MX

TURBO

When a Distance or Sample Count Is set

In Turbo Set Up mode, "SPD" (Speed)

indicator will be illuminated at bottom of

display. The number you enter should

correspond to the Distance or Sample

Count you want to use for the Speed

or Rate Computation. "P-HR" in display

means watch is set to compute "per

Hour" rate, and "P-Mn" means watch is

set to compute a "per Minute" rate.

If you want the watch to compute in "per

Sec" rate, divide the Distance or Sample

Count (Strokes, Strides, Units, etc.) by

60, then enter it.

For example, let's say that you are at a

race track with a course that is one mile

long. If you set the Distance to 1.00 and

the rate to "P-HR, " and then time several

laps, the Average Speed recorded by the

watch will be in miles per hour.

Speed/Rate Function Operation

S2 – Start (Shows Running LAP Time)

S2 – Split* (Top and Bottom show

SPEED/RATE 1/LAP 1)

S2 – Split* (Top and Bottom show

SPEED/RATE 2/LAP 2)

S2 – Split* (Top and Bottom show

SPEED/RATE 3/LAP 3)

S2 (2sec) – Reset LAP and SPEED/RATE

to zero**

*For only chance to view Total Average

Speed/Rate, push M.

Memory Review (before Resetting)

M – Review* (Bottom shows AVE

TOTAL SPEED/RATE, Top shows TOTAL

ELAPSED TIME)

M – Review* (Bottom shows AVE LAP

Split, Top shows TOTAL ELAPSED TIME)

M – Review (Shows last SPEED/RATE

and LAP Split)

M – Review (Shows next SPEED/RATE

and LAP Split, in reverse order)

*Reviews at any time in reverse numerical

order. Hold down for Rapid Review.

**Reset before 30 hrs. (end of range) and

rollover.

1 1

S3 & M