Sharp Carousel R-995J Panduan Pengoperasian - Halaman 6
Jelajahi secara online atau unduh pdf Panduan Pengoperasian untuk Oven Microwave Sharp Carousel R-995J. Sharp Carousel R-995J 48 halaman. Convection microwave oven
Juga untuk Sharp Carousel R-995J: Panduan Servis (48 halaman)
Halaman Cetak
A42404,SCA/SCNZ R995J O/M
INSTALLATION INSTRUCTIONS
1. Remove all packing materials from the oven cavity, (do not remove the waveguide cover), and the feature sticker
from the outside of the door, if there is one. Check the unit for any damage, such as a misaligned door, damaged
gaskets around the door or dents inside the oven cavity or on the door. If there is any damage, please do not operate
the oven until it has been checked by a SERVICE CENTRE APPROVED BY SHARP and repaired, if necessary.
2. Accessories provided
1) Turntable tray
2) Turntable support plate
3) Low rack
4) High rack
5) Defrost rack
6) Operation manual
7) Cook book
3. Since the door may become hot during cooking, you should
place or mount the oven so that the bottom of the oven is 80
cm or more above floor. You should also keep children
away from the door to prevent them burning themselves.
4. Place the turntable support plate over the turntable motor
shaft on the floor of the cavity.
Then place the turntable on the turntable support plate.
Make sure the turntable and support plate are centrally located and locked together. NEVER operate the oven
without the turntable support plate and turntable.
5. The oven should not be installed in any area where excessive heat and steam are generated, for example, next to
a conventional oven unit. When the oven is mounted on a kitchen benchtop, allow at least 40 cm on the top, 5 cm
on both sides and at the rear of the oven for adequate air circulation. The ventilation openings should not be blocked.
WARNING: The electrical outlet must be readily accessible so that the unit can be unplugged easily in an emergency.
6. Neither the manufacturer nor the distributors can accept any liability for damage to the machine or personal
injury for failure to observe the correct electrical connecting procedure.
The A.C. voltage must be single phase • 230V-240V, 50Hz
7. This appliance must be earthed.
8. Operate the oven from a general purpose domestic outlet.
If a generator is used, do not operate the oven with non-sinusoidal outputs.
9. Building the oven into the wall. A Sharp built-in kit model number RK-J90W is available which enables the
microwave oven to be integrated within a kitchen, the kit is available from your retailer. This built-in kit has
been tested according to Australian Standards. Sharp does not recommend the use of any other built-in kit.
If the oven is to be positioned near a conventional oven, ensure that adequate space is allowed, and a suitable
heat shield is incorporated between the two to prevent damage to the oven and the built-in kit caused by heat.
10. Before using CONVECTION HEATER ELEMENTS for the first time, operate the oven without food for 20
minutes at 250°C. This will allow the oil that is used for rust protection to be burned off.
OVEN DIAGRAM
F
0
B
3
5
4
1. Oven lamp
2. Door hinges
3. Door safety latches
4. See through door
5. Door seals and sealing
surfaces
6. Touch Control Panel
7. Digital readout
WARNING:
The accessories will become very hot when in use. Use thick oven gloves when inserting/removing the food or
turntable from the oven to PREVENT BURNS.
SCA/SCNZ R995J 1-6
8 1
A
9
3
8. Waveguide cover (Do not remove)
9. Turntable motor shaft
10. Convection air openings
11. Menu Label for Intelligent Sensor
12. Rating label
13. Access cover for oven
lamp replacement
14. Ventilation openings
5
D
7
6
E
2
H
5
04.8.4, 10:47 AM
Turntable
Turntable
support plate
C
G
I
J
15. Power supply cord
16. Oven cavity
17. Outer cabinet
18. Low rack
19. High rack
20. Defrost rack