Siemens SIMATIC ET 200SP Manual - Halaman 31

Jelajahi secara online atau unduh pdf Manual untuk Peralatan Industri Siemens SIMATIC ET 200SP. Siemens SIMATIC ET 200SP 49 halaman. Distributed i/o system
Juga untuk Siemens SIMATIC ET 200SP: Manual (40 halaman), Panduan Pengguna (21 halaman), Manual (34 halaman), Manual (48 halaman), Manual (30 halaman), Manual (34 halaman), Informasi Produk (38 halaman), Manual (37 halaman), Manual (36 halaman), Manual (44 halaman), Manual (31 halaman), Manual (35 halaman), Manual (23 halaman), Panduan Konfigurasi (20 halaman), Manual (34 halaman), Manual (29 halaman), Manual (33 halaman), Manual (31 halaman), Panduan Pengguna (32 halaman), Manual (31 halaman), Manual (28 halaman), Manual (41 halaman), Manual (32 halaman), Manual (49 halaman), Manual (24 halaman), Manual (34 halaman), Manual (41 halaman), Manual (30 halaman), Manual (31 halaman), Manual (27 halaman), Manual (24 halaman), Manual (24 halaman), Manual (25 halaman), Manual (40 halaman), Manual (38 halaman), Manual (39 halaman), Informasi Produk (24 halaman), Manual (32 halaman), Informasi Produk (10 halaman), Panduan Peralatan (43 halaman), Manual (33 halaman), Panduan Peralatan (44 halaman), Petunjuk Pengoperasian Asli (6 halaman), Manual (35 halaman), Manual (28 halaman), Panduan Peralatan (32 halaman), Manual (50 halaman), Manual (30 halaman), Manual (26 halaman), Manual (28 halaman), Manual (34 halaman), Manual (44 halaman), Manual (33 halaman), Panduan Peralatan (42 halaman), Manual Petunjuk Asli (16 halaman)

Halaman Cetak
Siemens SIMATIC ET 200SP Manual
Interrupts/diagnostics interrupts

5.3 Diagnostics alarms

Diagnostics interrupt
The module generates a diagnostics interrupt at the following events:
● Short-circuit (current and voltage 1 to 5 V)
● Wire break (current)
● High limit violated
● Low limit violated
● Error
● Parameter assignment error
● No load voltage
● Channel temporarily unavailable
5.3
Diagnostics alarms
A diagnostics alarm is generated and the DIAG-LED flashes on the module for each
diagnostics event. You can read out the diagnostics alarms, for example, in the diagnostics
buffer of the CPU. You can evaluate the error codes with the user program.
Table 5- 5
Diagnostics alarms, their meanings and corrective measures
Diagnostics alarm
Short-circuit (current)
Short-circuit (1 to 5 V)
Wire break (current)
High limit violated
Low limit violated
Error
Parameter assignment
error
30
Error code
Meaning
1
Encoder supply to ground
H
Input after encoder supply
1
Short circuit of input signal
H
Open input
6
Impedance of encoder circuit too high
H
Wire break between the module and sen-
sor
Channel not connected (open)
7
Value is above overrange.
H
8
Value is below underrange.
H
9
Internal module error has occurred (diag-
H
nostics alarm on channel 0 applies for the
entire module).
10
The module cannot evaluate parame-
•
H
ters for the channel.
Incorrect parameter assignment.
•
Solution
Correct interplay between module and
encoder
Correct interplay between module and
encoder
Connect input
Use a different encoder type or modify
the wiring, for example, using cables
with larger cross-section
Connect the cable
Deactivate diagnostics
•
Connect the encoder contacts
•
Correct the output value
Correct the output value
Replace the module
Correct the parameter assignment
(wire break diagnostics set only with
the permitted measuring ranges).
Analog input module AI 2xU/I 2-/4-wire HS (6ES7134-6HB00-0DA1)
Manual, 09/2018, A5E03576060-AF