Siemens WM10A166GC Manual - Halaman 2

Jelajahi secara online atau unduh pdf Manual untuk Mesin cuci Siemens WM10A166GC. Siemens WM10A166GC 8 halaman.

Halaman Cetak

Safety instructions

Before washing for the first time

– Read the instruction manual and installation instructions and all other information enclosed

with the washing machine and act accordingly.

– Retain the documents for subsequent use.

Risk of electric shock

– Never pull the cable to disconnect the mains plug.

– Never insert/disconnect the mains plug with damp hands.

Danger to life

For worn-out appliances:

– Disconnect the mains plug.

Care

– Sever the mains cable and discard along with the plug.

– Destroy the lock on the washing machine door. This will prevent

children from locking themselves in and risking their lives.

Danger of suffocation

– Keep packaging, film and packaging parts out of the reach of

children.

Risk of poisoning

– Keep detergents and care products out of the reach of children.

Risk of explosion

– Items of laundry pretreated with cleaning agents containing

solvents, e.g. stain remover/cleaning solvent may cause an

explosion after being loaded into the washing machine.

Rinse items of laundry thoroughly by hand beforehand.

1. Pull out, press insert down, remove drawer completely.

Risk of injury

– The washing machine door can become very hot.

2. To remove the insert: press the insert upwards from below with your

– Be careful when draining hot detergent solution.

– Do not climb onto the washing machine.

3. Clean the detergent dispenser tray and insert with water and a brush and

– Do not lean on the open washing machine door.

– Do not reach into the drum if it is still rotating.

4. Attach the insert and engage (connect the cylinder to the guide pin).

– Be careful when opening the detergent drawer while the machine

5. Push in the detergent drawer.

is in operation.

Consumption values

Electricity

Programme

Load

Water**

Programme

duration**

consumption**

Koge-/kulørtvask

5 kg

0,31 kWh

54 l

100 min

(Cottons) 30 °C*

Koge-/kulørtvask

5 kg

0,55 kWh

54 l

100 min

(Cottons) 40 °C*

Koge-/kulørtvask

5 kg

0,80 kWh

54 l

115 min

Information to indicator lights

(Cottons)60 °C*

Koge-/kulørtvask

5 kg

0,85 kWh

41 l

175 min

Indicator lights for status displays flash:

(Cottons) 60 °C Intensiv

(wash) and

(Intensive)*

(rinse)

Koge-/kulørtvask

5 kg

1,90 kWh

61 l

110 min

(wash) and

(Cottons) 90 °C

(spin)

Strygelet (Easy-Care) 40 °C*

2,5 kg

0,45 kWh

50 l

75 min

(rinse) and

Finvask (Delicate) 30 °C

2 kg

0,30 kWh

55 l

50 min

(spin)

Uld-/håndvask (wool) 30 °C

2 kg

0,20 kWh

35 l

55 min

* Programme setting for testing in accordance with valid standard EN60456.

** The values deviate from the indicated values depending on water pressure, hardness, and inlet temperature, ambient

temperature, type, amount and soiling of the laundry, detergent used, fluctuations in the power supply and selected

additional functions.

Maintenance

Do not load any laundry into the machine. Turn on the tap. Add the following to compartment

Detergent solution pump

II:

Turn the programme selector to Fra (Off) and disconnect the mains plug.

– approx. 1 litre water

– detergent (dosage according to the manufacturer's instructions for light soiling and the

1. Remove the service flap for detergent solution pump.

appropriate degree of water hardness)

2. Carefully unscrew the pump cover (residual water).

Set the programme selector to Strygelet (Easy-Care) 60 °C and select Start

. At the end

3. Clean the interior, pump cover thread and pump housing (the impeller in

of the programme, turn the programme selector to Fra (Off).

the detergent solution pump must rotate).

– Risk of electric shock.Disconnect the mains plug.

4. Replace the pump cover and screw it tightly.

5. Place the service flap back.

– Risk of explosion. No solvents.

To prevent unused detergent from flowing straight into the drain during the next wash:

Machine housing, control panel

Pour 1 litre of water into compartment II and start the Udpumpning (Empty) programme.

– Wipe with a soft, damp cloth.

Drainage hose at the siphon

– Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners).

Turn the programme selector to Fra (Off) and disconnect the mains plug.

– Remove detergent and cleaning agent residue immediately.

– Do not clean with a jet of water.

1. Loosen the hose clamp, carefully remove the drainage hose

(residual water).

Cleaning the detergent drawer ...

2. Clean the drainage hose and siphon connecting piece.

... if it contains detergent or fabric softener residues.

3. Reattach the drainage hose and secure the connection with the hose

clamp.

finger.

Filter in the water supply

Risk of electric shock

dry it.

Do not immerse the HydroSafe safety device in water (contains an electric valve).

Reduce the water pressure in the supply hose:

Leave the detergent drawer open so that any residual water can

evaporate.

1. Turn off the tap.

2. Select any programme (except Centrifugering (Spin)/ Udpumpning

(Empty).

Drum

3. Select Start

Leave the washing machine door open so that the drum can dry out.

4. Turn the programme selector to Fra (Off). Disconnect the mains plug.

Rust stains - use chlorine-free cleaning agent, not steel wool.

Descaling

Ensure there is no laundry in the machine

5. Clean the filter:

Disconnect the hose from the tap.

Descale the appliance according to the descaler manufacturer's instructions. This should not

Clean the filter using a small brush.

be necessary if the correct dosage of detergent is used.

and/or for Standard and Aqua-Secure models:

Remove the hose on the rear of the appliance,

Remove the filter with pliers and clean.

6. Connect the hose and check the leak tightness of the

Close the washing machine door properly; laundry may be caught.

connection points.

– Open the tap completely.

– Supply hose kinked or trapped.

– Clean the filter

page 10, Water pressure too low.

Detergent solution pump blocked; Clean the detergent solution pump

page 10.

Drainage hose/waste pipe blocked; Clean the drainage hose at the siphon

page 10.

– Risk of scalding. Allow the

detergent solution to cool down.

What to do if ...

– Turn off the tap.

Water is leaking out.

– Attach/replace the drainage hose correctly.

– Tighten the screw connection of the supply hose.

No water supply.

– Start

Detergent not dispensed.

– Tap not turned on?

– Filter blocked? Clean the filter

– Supply hose kinked or trapped?

Washing machine door

– Safety function active. Wait approx. 2 minutes.

cannot be opened.

– Is

Programme does not

– Start

start.

– Washing machine door closed?

Detergent solution is not

– Clean the detergent solution pump

drained.

– Clean the waste pipe and/or drainage hose.

– Is

Water not visible in the

– Not a fault - water below the visible area.

drum.

Unsatisfactory spin

– Not a fault - the unbalanced-load detection system has cancelled

result.

the spin cycle because of uneven distribution of the laundry.

Laundry wet/too damp.

Distribute small and large items of laundry evenly inside the

drum.

– Selected speed too low?

Spin cycle performed

– Not a fault - unbalanced load detection system adjusts the

several times.

imbalance.

Residual water in the

– Not a fault - the action of the care product is not affected.

compartment for care

– Clean the insert if necessary –> page 9.

products.

Odour formation in the

– Run programme Koge-/kulørtvask (Cottons) 90 °C without

washing machine.

laundry. Use standard detergent.

. Let the programme run for approximately 40 seconds.

Foam escaping from the

– Too much detergent used?

detergent drawer.

If foam is escaping from the detergent drawer:

Mix 1 tablespoon of fabric softener with ½ litre of water and pour

into compartment II (not with outdoor or down fabrics).

– Reduce the detergent dosage for the next wash cycle.

Intense noise formation,

– Are the appliance feet fixed?

vibrations and

Secure the appliance feet

"wandering" during the

– Transportation safety devices removed?

spin cycle.

Remove the transportation safety devices

instructions.

Indicator lamps do not

– Power cut?

function during

– Fuses triggered? Reset/change the fuses.

operation.

– If the fault occurs repeatedly, call the after-sales service.

Programme sequence

– Not a fault - unbalanced load detection system adjusts

longer than usual.

imbalance by repeatedly distributing the laundry.

– Not a fault - foam detection system active - adds an additional

rinse cycle.

Detergent residues on

– Occasionally, phosphate-free detergents contain water-insoluble

the laundry.

residues.

– Select Skyl (Rinse) or brush the laundry after washing.

If you cannot correct a fault yourself or a repair is required:

– Turn the programme selector to Fra (Off) and remove the mains plug from the socket.

– Turn off the water supply and call the after-sales service

not selected?

page 10.

(no spin = without final spin) selected? –> page 1, 5.

selected?

page 10.

Observe the safety

instructions on

(no spin = without final spin) selected? –> page 1, 5.

page 8.

page 5.

Installation instructions.

Washing

Installation

machine

Instruction manual

Read these instructions and the separate installation

instructions before operating the washing machine.

Installation instructions.