Sony R-D-S EON MHC-2900 Panduan Petunjuk Pengoperasian - Halaman 16

Jelajahi secara online atau unduh pdf Panduan Petunjuk Pengoperasian untuk Sistem stereo Sony R-D-S EON MHC-2900. Sony R-D-S EON MHC-2900 35 halaman.

Halaman Cetak

=> continued

Recording a CD Manually

You can record a CD as you like, for

instance, record just the songs you want or

record from the middle of the tape. Before

performing any operations, set the

amplifier to EFFECT OFF mode.

POWER—ON

1 Press & OPEN/CLOSE on the CD

player and place a CD. Then, press

@ OPEN/ CLOSE again to close the

tray.

2 Press & and insert a blank tape into

deck B. Make sure the tabs on the

cassette have not been removed.

3 Press CD to select the CD player.

4 select dual or single-sided recording

with DIRECTION and press DISPLAY.

To record

One side

appears

Both sides*

Recording always stops at the end of the

reverse side."Be sure to start from the

front side.

5 when you want to reduce the hiss noise

in low-level high-frequency signals,

press DOLBY NKR to select B or C.

Dolby C provides greater noise

reduction benefit than Dolby B.

Chapter 4 : the Tape Player

Press DIRECTION so that

or RELAY appears

6 Press @ REC.

Deck B stands by for recording.

The [> (for front side) or <I (for

reverse side) indicator lights steadily to

show you which side will start

recording. The other indicator flashes

for a few seconds, then disappears.

For a full explanation of the >> and <1

indicators, see "What the [> and <J

indicators indicate" in "Recording a CD

Automatically".

7 if the indicator for the side you want to

start recording does not light, press >

or <<] to light the side to start recording.

If it lights, skip to step 8.

8 Press Il PAUSE on the tape player to

release recording pause.

Recording starts. You can also start

recording by pressing >> or <1.

9 Press > on the CD player.

The CD player starts playing.

Press

Stop recording

Ml on the deck B

Pause recording

1 PAUSE on the

deck B

Stop CD play

@ on the CD player

Pause CD play

4 on the CD player

Adjusting the volume will not affect

the recording level

But this control will change the sound

levels you hear through speakers or

headphones.

Recording equalized or processed

sounds

If an audio emphasis setting or a Personal

File is selected on the amplifier, the

processed sound can be recorded. When

playing back a recording that was made of

a processed sound, use EFFECT OFF mode.

If the processed sound is recorded and then

the playback is processed again, the

resulting sound may be distorted. To make

a flat (unprocessed) recording, use EFFECT

OFF mode.

Inserting a Blank Space

During Recording

To activate the AMS function, it is

necessary to insert a blank space between

tracks.

POWER—ON

the position where you want to insert

the blank space.

The REC indicator flashes and the tape

runs without recording. After about

4 seconds, the REC indicator and the

PAUSE indicator light, and the unit

enters the recording pause mode.

2 Press II PAUSE at the position where

you want to start recording again.

Recording restarts.

To make a blank of more than

4 seconds

Press OQ REC MUTE for as long as needed.

The indicator on the button flashes faster

after 4 seconds have elapsed. The tape

pauses when you release OQ REC MUTE.

To make a blank within 4 seconds

Press

@ REC while the indicator on the

button is flashing.

Recording a CD:

Selecting Tape Length

Automatically (tape

select edit)

You can have the stereo system select and

indicate the most suitable tape length for

recording each disc automatically.

You cannot use Tape Select Edit for discs

which contain 21 tracks or more.