Sony R-D-S EON MHC-2900 Panduan Petunjuk Pengoperasian - Halaman 18

Jelajahi secara online atau unduh pdf Panduan Petunjuk Pengoperasian untuk Sistem stereo Sony R-D-S EON MHC-2900. Sony R-D-S EON MHC-2900 35 halaman.

Halaman Cetak

> continued

5 Choose how you want the tracks to be

recorded.

To fit as many tracks on the tape as

possible while changing the original

CD order as little as possible (time

edit)

Press EDIT twice.

"EDIT" appears in the display.

To fit as many tracks on the tape as

possible letting the CD player

change the original CD order (just

edit)

Press EDIT three times.

"JUST EDIT" appears in the display.

6 Press 4 << or PP PPI to designate

the tape length or "~.--".

Choose the indication for tapes of

corresponding minute length.

As you press the button, the indication

changes as follows:

~~ C-A6OC-54

(23.00) (27.00) S

C-90C-744C-60

(45.00) (37.00) (30.00)

To specify the recording time

Use the numeric buttons (1 to 10) on the

remote commander to specify the

recording time on each side of the

cassette.

e.g. To specify 11 minutes 30 seconds,

press 1,1, 3,10.

7 Press EDIT.

The player determines the tracks to be

recorded on side A automatically.

Selections to be recorded

Total playing time

8 When you record on both sides, press

EDIT again.

The player determines the tracks to be

recorded on side B.

Chapter 4 : the Tape Player

9 Press DISPLAY to select the display

for the tape player.

1 0 When you want to reduce the hiss

noise in low-level high-frequency

signals, press DOLBY NR to select B

orc.

Dolby C provides greater noise

reduction benefit than Dolby B.

1 Tress CD SYNCHRO.

Deck B stands by for recording.

1 2 Press HI PAUSE on the tape

player to release recording pause.

Recording starts.

To stop recording

Press Hi on deck B.

To select the desired tracks

beforehand

You can place priority on some tracks to be

recorded by selecting them before

programming them up to 20 tracks. See

"Playing Tracks inthe Desired Order

(programme play)."

To check the order

Press CHECK repeatedly.

As you press the button, the programme for

side A, "P" and the programme for side B

appear in order.

To cancel time edit/just edit

Before you press EDIT on step 5, press il

to cancel. After you press EDIT on step 5,

press CONTINUE.

Recording equalized or processed

sounds

If audio emphasis setting or a Personal File

is selected on the amplifier, the processed

sound can be recorded. When playing back

a recording that was made of a processed

sound, use EFFECT OFF mode. If the

processed sound is recorded and then the

playback is processed again, the resulting

sound may be distorted. To make a flat

(unprocessed) recording, use EFFECT OFF

mode.

if programming takes too long during

just edit

Some CDs with many tracks may take a

while for the CD player to programme. In

this case, press Ml.

The programme will be the closest time you

specified until

was pressed.

Peo

Recording a CD:

Specifying Track

Order (programme

edit)

You can adjust the total recording time to

the tape length while making a programme.

POWER->ON

1 Following the procedure "Playing

Tracks in the Desired Order

(programme play)", programme the

tracks you want to record for side A.

Make sure to programme the tracks so

that the total playing time of side A does

not exceed the tape length of one side.

2 Press Il on the remote commander.

"P" appears in the display and the total

playing time is reset to "0.00".

3 Programme the tracks you want to

record for side B as the same way as

you did for side A.