Digitrax SoundFX SFX004 Manual - Halaman 5

Jelajahi secara online atau unduh pdf Manual untuk Konverter Media Digitrax SoundFX SFX004. Digitrax SoundFX SFX004 12 halaman.

Halaman Cetak

C C u u s s t t o o m m i i z z i i n n g g Y Y o o u u r r D D e e c c o o d d e e r r

Your Digitrax SFX004 Soundbug

ate sound using address 03 with no additional programming. On your Digitrax

system, simply select the locomotive's address and the sound will start. On

some DCC systems, it is necessary to select the locomotive address AND send

a command to start the sounds.

When used in conjunction with a separate DCC motor decoder in a single loco-

motive it is most practical to program both decoders to the same address and

operating modes.

For a more prototypical railroading experience, your decoder can be cus-

tomized for your specific locomotive by programming some of the

Configuration Variables, or CVs, available. Digitrax Sound decoders can be

programmed using either the direct method on a programming track or with the

operations mode using the main line. See the Digitrax Decoder Manual or the

Digitrax web site for more information.

Intial Test and Programming: This decoder is preprogrammed and tested

with a Steam locomotive sound scheme, and is ready to operate on factory

default address 03. Before customizing the decoder it is useful to run it on

the factory default address 03 to check the installation. The following sec-

tions show how to change the locomotive address and customize the

decoder

For more information on decoder installation and programming techniques and

examples visit the www.digitrax.com

C C h h a a n n g g i i n n g g t t h h e e D D e e c c o o d d e e r r A A d d d d r r e e s s s s

The first CV most people change is the decoders address. This lets you inde-

pendently control each loco with its own unique address. Digitrax decoders are

shipped with CV01 (AD2), the two digit address, set to 03. Following is a brief

description of how to change the decoder address with a Digitrax DT series

throttle. See your Starter Set Manual for complete programming instructions.

1. Place the loco on the programming track or on the main line.

2. Enter the programming mode using your DCC system/throttle. On DT400

press PROG until you see "Pd" if using a programming track or "Po" if

using the main line.

3. Use your throttle to choose the address you want to set up for the decoder.

On the DT400 use the left knob to dial AD2 for two digit programming, use

the right knob to dial up the address, click the right knob to change to AD4

for programming 4 digit addresses.

2 2 4 4 4 4 3 3 T T r r a a n n s s m m i i t t t t e e r r R R D D

P P a a n n a a m m a a C C i i t t y y , , F F l l 3 3 2 2 4 4 0 0 4 4

w w w w w w . . d d i i g g i i t t r r a a x x . . c c o o m m

is ready to run and will operate and gener-

www.digitrax.com

8 8 5 5 0 0 - - 8 8 7 7 2 2 - - 9 9 8 8 9 9 0 0

T T

8 8 5 5 0 0 - - 8 8 7 7 2 2 - - 9 9 5 5 5 5 7 7

F F

s s a a l l e e s s @ @ d d i i g g i i t t r r a a x x . . c c o o m m

E E