Epson PowerLite 735c Informasi Produk - Halaman 3

Jelajahi secara online atau unduh pdf Informasi Produk untuk Perangkat lunak Epson PowerLite 735c. Epson PowerLite 735c 14 halaman. Release of check tool for network projectors v1.00 for windows
Juga untuk Epson PowerLite 735c: Panduan Pengguna (42 halaman), Panduan Pengoperasian (36 halaman), Panduan Pengguna (29 halaman), Spesifikasi (2 halaman), Panduan Pengoperasian (47 halaman), Daftar Bagian (1 halaman), Buletin Dukungan Produk (30 halaman), Panduan Instalasi (19 halaman), Panduan Pengaturan Cepat (2 halaman), Buletin Dukungan Produk (25 halaman), Buletin Dukungan Produk (38 halaman), Buletin Dukungan Produk (12 halaman), Buletin Dukungan Produk (42 halaman), Buletin Dukungan Produk (22 halaman), Buletin Dukungan Produk (28 halaman), Buletin Dukungan Produk (41 halaman), Buletin Dukungan Produk (34 halaman), Buletin Dukungan Produk (38 halaman), Buletin Dukungan Produk (28 halaman), Buletin Dukungan Produk (15 halaman), Buletin Dukungan Produk (22 halaman)

Halaman Cetak

Use the figure below as a guideline to help you determine how

far from the screen to place the projector. Image size generally

increases with distance, but may vary depending on how you

position the zoom ring and whether you have adjusted the

image size with other settings.

33 to 38.5 ft

6.5 to 7.5 ft

If you place the projector below the level of the screen, you'll

have to tilt it up by extending the feet as shown on page 5.

This causes the projector to lose its square shape, but the

projector automatically compensates. You can manually

correct the distortion by pressing the

described on page 5.

If you place the projector level with the bottom of the screen,

the image will be square and you won't have to adjust it. If

you place the projector higher than the bottom of the screen,

the image will still be square, but you won't be able to fill the

whole screen with the image.

Starting Up the Projector

Make sure your projector and other equipment are set up and

connected correctly. Then turn on your projector, as described

below, followed by any equipment you've connected to it. You

can turn on your computer and video equipment in any order,

but if you have both a computer and video source connected,

you may have to switch to the desired source as described on

page 4.

3 to 4 ft

Distance

from screen

button as

Keystone

Ideal

height

EPSON PowerLite 735c Projector

Turning On the Projector

Follow these steps to plug in and turn on the projector:

1. Remove the lens cap.

Caution: Do not use the projector with the lens cap in place.

The heat generated by the lens can damage the cap.

2. Connect one end of the power cord to the projector's

power inlet.

3. Connect the other end to an electrical outlet.

The P power light on top of the projector turns orange,

indicating that the projector is receiving power but not yet

turned on.

4. Press the red P

Power

can also use the P

Power

button

The P power light flashes green as the projector warms up,

and the projection lamp comes on in about 40 seconds.

Then the power light stays green.

Warning: Never look into the lens when the lamp is on. This

can damage your eyes.

5. Select the source as follows:

❏ On the control panel, the

between equipment connected to the Video, S-Video,

and Computer/Component Video ports, or to

EasyMP

(for wireless network and memory card

™

presentations).

❏ On the remote control, the

switches between a computer source and EasyMP. The

S-Video/Video

source and standard composite video source.

2/03

button on top of the projector. You

button on the remote control.

Power

button switches

Source

Comp/EasyMP

button switches between an S-Video

EPSON PowerLite 735c Projector

button