Epson PowerLite 8300i with EasyMP.net module Panduan Cepat - Halaman 9

Jelajahi secara online atau unduh pdf Panduan Cepat untuk Perangkat lunak Epson PowerLite 8300i with EasyMP.net module. Epson PowerLite 8300i with EasyMP.net module 20 halaman. Release of check tool for network projectors v1.00 for windows
Juga untuk Epson PowerLite 8300i with EasyMP.net module: Panduan Pengguna (42 halaman), Panduan Pengoperasian (36 halaman), Panduan Pengoperasian (47 halaman), Pengaturan Cepat (2 halaman), Buletin Dukungan Produk (27 halaman), Daftar Bagian (1 halaman), Panduan Tambahan (2 halaman), Brosur & Spesifikasi (2 halaman), Panduan Pengguna (1 halaman), Buletin Dukungan Produk (25 halaman), Buletin Dukungan Produk (22 halaman), Buletin Dukungan Produk (28 halaman), Buletin Dukungan Produk (41 halaman), Buletin Dukungan Produk (34 halaman), Buletin Dukungan Produk (28 halaman), Buletin Dukungan Produk (15 halaman), Buletin Dukungan Produk (22 halaman), Pengaturan Cepat (2 halaman)

Halaman Cetak

Epson PowerLite 8300i with
EasyMP.net module Panduan Cepat

EPSON PowerLite 8300i Projector

Adjusting the Image

Once you see your image, you may need to make certain

adjustments.

Focusing and Zooming Your Image

Use the

buttons on the remote control (or on the

Focus

projector) to sharpen the image.

Use the

buttons to reduce or enlarge the image.

Zoom

Focus

Zoom

If the image still isn't large enough, you may need to move the

projector farther away from the screen. You can also use the

buttons on the remote control to zoom in on a

E-Zoom

portion of the image.

Note: The Focus and Zoom buttons won't work when the wide-

angle rear projection lens is installed.

Adjusting the Height of Your Image

If the image is too low on the screen, you can raise it using the

Lens Shift. This is the best method for adjusting the height of

the image. If you need to raise the image further, you can tilt

the projector upward by extending the feet.

Using the Lens Shift

To raise or lower the image, use the

remote control (or on the projector).

Note: The Lens Shift buttons won't work when the wide-angle

rear projection lens is installed.

EPSON PowerLite 8300i Projector

buttons on the

Lens Shift

Raising the Projector's Feet

If you need to raise the image further, you can incline the

projector:

1. Stand behind the projector. Press the foot release buttons

on each side and lift the front of the projector.

2. Once the image is positioned where you want it, release the

buttons to lock the feet in position.

3. If necessary, you can level the picture or fine-tune the

height by turning the projector feet.

Raising the projector causes the image to distort or

"keystone," but you can manually correct the shape as

described in the next section.

Adjusting the Image Shape

In most cases, you can maintain a square or rectangular image

by placing the projector directly in front of the center of the

screen and using the Lens Shift (instead of tilting the projector

upward) to adjust the image height.

If this isn't possible, use one of these methods to correct the

image shape:

If the image tapers inward on

the right and left sides only,

use Keystone correction as

described on the next page.

If the image looks uneven on

all sides, or just on the top

and bottom, you can adjust

its shape using Quick Corner.

You cannot use both Keystone correction and Quick Corner

at the same time.

5/03