Epson PowerLite 9300i - PowerLite 9300NL Multimedia Projector Panduan Cepat - Halaman 9

Jelajahi secara online atau unduh pdf Panduan Cepat untuk Perangkat lunak Epson PowerLite 9300i - PowerLite 9300NL Multimedia Projector. Epson PowerLite 9300i - PowerLite 9300NL Multimedia Projector 20 halaman. Release of emp ns connection for windows & mac upgrade from v2.50 to v2.51
Juga untuk Epson PowerLite 9300i - PowerLite 9300NL Multimedia Projector: Panduan Pengguna (42 halaman), Panduan Pengoperasian (36 halaman), Brosur & Spesifikasi (2 halaman), Panduan Pengoperasian (47 halaman), Buletin Dukungan Produk (27 halaman), Pengaturan Cepat (2 halaman), Suku Cadang Pengganti (1 halaman), Buletin Dukungan Produk (25 halaman), Buletin Dukungan Produk (22 halaman), Buletin Dukungan Produk (28 halaman), Buletin Dukungan Produk (41 halaman), Buletin Dukungan Produk (15 halaman), Buletin Dukungan Produk (22 halaman)

Halaman Cetak
Epson PowerLite 9300i - PowerLite 9300NL Multimedia Projector Panduan Cepat

Adjusting the Height of Your Image

If the image is too low on the screen, you can raise it using the
Lens Shift. This is the best method for adjusting the height of
the image. If you need to raise the image further, you can tilt
the projector upward by extending the feet.
Using the Lens Shift
To raise or lower the image, use the
remote control (or on the projector).
Note: The Lens Shift buttons won't work when the wide-angle
rear projection lens is installed.
Raising the Projector's Feet
If you need to raise the image further, you can incline the
projector:
1. Stand behind the projector. Press the foot release buttons
on each side and lift the front of the projector.
2. Once the image is positioned where you want it, release the
buttons to lock the feet in position.
3. If necessary, you can level the picture or fine-tune the
height by turning the projector feet.
Raising the projector causes the image to distort or
"keystone," but you can manually correct the shape as
described in the next section.
buttons on the
Lens Shift
Lens Shift
EPSON PowerLite 9300i Projector

Adjusting the Image Shape

In most cases, you can maintain a square or rectangular image
by placing the projector directly in front of the center of the
screen and using the Lens Shift (instead of tilting the projector
upward) to adjust the image height.
If this isn't possible, use one of these methods to correct the
image shape:
If the image tapers inward on
the right and left sides only,
use Keystone correction as
described on the next page.
If the image looks uneven on
all sides, or just on the top
and bottom, you can adjust
its shape using QuickCorner.
You cannot use both Keystone correction and QuickCorner at
the same time.
Using Keystone Correction
To adjust your image when the right and left sides are uneven,
do one of the following:
Use the
Keystone
to adjust the image shape.
Keystone buttons
Or use the Keystone function in the
projector's menu system. (Press the
button on the remote control, select the
menu, and press
Setting
Setting menu, select
. Then select
Enter
. Adjust the setting as needed.)
Enter
Note: After using Keystone correction, the image will be slightly
shorter. If it's important to maintain the correct aspect ratio, you
can stretch the image to its proper size using the
the Keystone menu.
10/03
buttons on the projector's control panel
Menu
. From the
Enter
and press
Keystone
and press
V-Keystone
Height
EPSON PowerLite 9300i Projector
Menu button
setting in
9
-