Cru Power E-1000 Manual

Jelajahi secara online atau unduh pdf Manual untuk Inverter Cru Power E-1000. Cru Power E-1000 2 halaman. Power inverter

Halaman Cetak

DC to AC

Remote Control

Overtemp LED

POWER

(24V)

OVER

TEMP

OVER

LOAD

OFF

ON/OFF switch

Please keep switch

in the OFF position

during installation.

Overload LED

Firstly, thank you for purchase

our product.

Please read this manual carefully before

installing or using this product.

Specification

Firstly, thank you for purchase our

product.

Please read this manual carefully

before installing or using this

product.

SPECIFICATIONS

Model No.

HT-E-1000-12 HT-E-1000-24

AC100V / AC110V

AC Output Voltage

AC120V / AC220V

AC230V / AC240V

Input low voltage

DC10.5V

0.5V

alarm

Input high voltage

DC15V

0.5V

shut-down

Input low voltage

DC10V

0.5V

shut-down

Output power

1000W

continuous

50Hz/60Hz

Output Frequency

Efficiency

＞85﹪

AC100V~AC120V＜0.6 A

No load current draw

AC220V~AC240V＜1.0 A

Dimensions

340*179*82

(L×W×H)(by mm)

Net weight (by Kg/s)

3.20

Modified Sine Wave

Output wave

Regulation

±5﹪

Over Temperature

55℃ ±5℃

protection

YES

Cooling fan

Output reverse

YES

protection

Overload protection

YES

Introduction

The power inverter series are the member

of the most advanced line of mobile AC

power systems available.

This model is used in a wide range of

application including remote homes, RVs,

sailboats and powerboats. It will operate

most televisions and VTR's, personal

computers, small appliances and tools such

as drills, sanders, grinders, mixers and

blenders.

To get the most out of the power inverter,

it must be installed and used properly.

Please read the instructions in this manual

before installing and using this model.

Name and Main function

1. Front view

a. ON/OFF switch:

Leave in the OFF position during installation.

b. Over heat protection:

LED sparkles when product temperature gets

high, it wou'd shut down automatically while

temperature arrives 55±5℃.

Power inverter

Front view

INPUT

LOAD(%)

INPUT

LOAD

（100％）

SWITCH

(12V)

1100

1000

900

800

700

600

500

400

300

200

VOLT

WATT

Input Volt and

load status indicator

Power LED

Remote Control

c. Overload protection:

Orange LED lights when inverter shut down

due to overloading. Interver would re-start

twice, if failed, inverter would shut down. Please

turn inverter OFF, reduce load and turn inverter

ON to reset.

d. LED display of Romote Control:

Display battery voltage and current. Current

should be in the green zone for continuous

operation. The inverter will operate for

several minutes when the current in the yellow

zone.

e. AC outlet:

Outlet sockets available:Australia/NZ

DC21.5V

DC30V

DC20V

2. Rear view:

2Hz

a. Ventilation window:

Do not obstruct, allow at least one inch for

airflow.

b. Battery terminals:

Connect to 12V/24V battery or other 12V/24V

power source. "+" is positive, "-" is negative.

Reverse polarity connection will blow internal

fuse and may damage inverter permanently.

c. Chassis ground lug:

Connect to earth ground or to vehicle chassis

using #8 AWG wire.

！

WARNING!!

Operation of the inverter without a proper

ground connection may result in an electrical

safety hazard.

Quick hook - up and testing

If you would like to quick hook-up the power

inverter and check its performance before

going ahead with your installation, please

follow these guideline

Unpack and inspect the power inverter,

check to see that the power switch in the

OFF position.

Connect the cables to the power input

terminals on the rear panel of power

inverter. The red terminal is positive (+)

and black terminal is negative (-).

Connect the cables into the terminals and

tighten the wing nut to clamp the wires

securely.

Connect the cable from the negative terminal

of the inverter to the negative terminal of the

power source. Make a secure connection.

！

CAUTION!!

Loosely tightened connectors result in excessive

drop and may cause overheated wires and

melted insulation.

Before proceed further, carefully check if the

terminals connect correctly.

manual

！

Reverse polarity connection will blow a fuse in

inverter and may permanently damage the

inverter. Damage caused by reverse polarity

connection is not covered by our warranty.

Connect the cable from the positive terminal

of inverter to the positive terminal of the power

source. Make secure connection.

！

AC Outlet sockets

You may observe a spark when you make this

It is suitable for Australia,

New Zealand, Canada,

connection since current may flow to charge

America, Europe, Japan

and Universal type.

capacitors in the power inverter.

Do not make this connection in the presence of

flammable fumes, explosions or fire may result.

Set power inverter switch to the OFF

position, the indicator lights may blink and

the internal alarm may sound momentarily.

This is normal. Plug the test load into the

AC receptacle on the front panel of the inverter.

Leave the test load switch off.

Set power inverter switch to the ON position

and turn the test load on, the inverter should

supply power to the load.

North America

1. Where to install

Europe

The power inverter should be installed in a

Universal

location that meets the following requirements:

Japan

a. Dry - Do not allow water to drip or splash on

the inverter.

b. Cool - Ambient air temperature should be

between 0°C and 40°C, the cooler environment

is better.

c. Ventilated - Allow at least one inch of

clearance around the inverter for airflow.

Ensure the ventilation openings on the rear

and bottom of the unit are not obstructed.

d. Safe - Do not install the inverter in the same

compartment as batteries or in any

compartment capable of storing flammable

liquids such as gasoline.

2. Cables

DC to AC inverters requires high amperage/low

voltage DC power to low amperage/high voltage

AC power. To operate properly connect inverter

DC input terminals direct to battery with heaviest

wire available see chart below:

Max Watts Out

100W

150W

300W

600W

1000W

1200W

1500W

1800W

2500W

3. Grounding

The power inverter has a lug on the rear panel

"chassis ground". This is to connect the chassis

of the power inverter to the ground. The ground

terminals in the AC outlets on the front panel of

the inverter are also connected to the ground lug.

The chassis ground lug must be connected to a

grounding point, which will vary depending on

where the power inverter is installed. In a vehicle,

connect the chassis ground to the chassis of the

vehicle. In a boat, connect to the boat's grounding

systems. In a fixed location, connect the chassis

ground lug to earth.

HT-E-152A2

CAUTION!!

WARNING!!

Installation

Approx. Amps

Teq'dWire Gauge

10A

15A

30A

60A

#6 or 2 X #10

100A

120A

150A

180A

2 X #4

250A

2 X #4

#16

#12

# 4