Pioneer DEH-3200UB Panduan Instalasi - Halaman 5

Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Penerima Mobil Pioneer DEH-3200UB. Pioneer DEH-3200UB 8 halaman. Cd rds receiver
Juga untuk Pioneer DEH-3200UB: Panduan Instalasi (6 halaman), Panduan Pengoperasian (28 halaman), Panduan Pengoperasian (31 halaman), Panduan Pengoperasian (29 halaman)

Halaman Cetak

9. Notes

1. This product

• Change the initial setting of this unit (refer to the

operation manual). The subwoofer output of this unit is

monaural (DEH-3200UB).

8. Antenna

• When using a subwoofer of 70 W (2 Ω), be sure to

jack

connect with Violet and Violet/black leads of this unit.

Do not connect anything with Green and Green/black

7. Fuse (10 A)

leads.

10. Note

11. Speaker leads

Depending on the kind of vehicle,

White:

Front left

the function of 2* and 4* may be

different. In this case, be sure to

White/black: Front left

connect 1* to 4* and 3* to 2*.

Gray:

Front right

Gray/black: Front right

Green:

Rear left

or subwoofer

Green/black: Rear left

or subwoofer

Violet:

Rear right

or subwoofer

Violet/black: Rear right

or subwoofer

12. Connect leads of the

same color to each other.

13. Yellow (2*)

14. Yellow (1*)

Back-up (or

Connect to the constant

accessory)

12 V supply terminal.

15. Red (4*)

16. Red (3*)

Accessory

Connect to terminal controlled by

(or back-up)

ignition switch (12 V DC).

17. Black (chassis ground)

Connect to a clean, paint-free metal location.

18. ISO connector

19. Yellow/black

Note

If you use an equipment with Mute

function, wire this lead to the Audio Mute

In some vehicles, the ISO connector may be

lead on that equipment. If not, keep the

divided into two. In this case, be sure to

connect to both connectors.

Audio Mute lead free of any connections.

23. For DEH-4200SD

24. To subwoofer output

2. Rear output or subwoofer output

(DEH-3200UB)

3. Rear output (DEH-4200SD)

25. To rear output

4. Front output (DEH-4200SD)

5. Subwoofer output

(DEH-4200SD)

26. To front output

6. Wired remote input

Hard-wired remote

control adaptor can

be connected (sold

separately).

28. Connect with RCA cables

(sold separately)

29. System remote control

20. Blue/white

Connect to system control

30. Front speaker

terminal of the power amp (max.

300 mA 12 V DC).

21. Blue/white (6*)

Connect to auto-antenna relay

31. Rear speaker

control terminal (max. 300 mA

12 V DC).

22. Blue/white (5*)

32. Subwoofer

The pin position of the ISO

connector will differ depending

33. Perform these connections when

on the type of vehicle. Connect

using the optional amplifier.

34. For DEH-3200UB

5* and 6* when Pin 5 is an

antenna control type. In another

type of vehicle, never connect

5* and 6*.

35. To rear output or

subwoofer output

37. Connect with RCA

cable (sold separately)

29. System remote control

36. Rear speaker

or subwoofer

Connecting the units

Note

• When this unit is installed in a vehicle without

ACC (accessory) position on the ignition switch,

red cable must be wired to the terminal that can

detect the operation of the ignition key. Otherwise,

27. Power amp

battery drain may result.

(sold separately)

27. Power amp

(sold separately)

27. Power amp

(sold separately)

ACC position

No ACC position

• Use this unit in other than the following

conditions could result in fire or malfunction.

— Vehicles with a 12-volt battery and negative

grounding.

— Speakers with 50 W (output value) and 4 ohm

to 8 ohm (impedance value).

• To prevent short-circuit, overheating or

malfunction, be sure to follow the directions

below.

— Disconnect the negative terminal of the

battery before installation.

30. Front speaker

— Secure the wiring with cable clamps or

adhesive tape. To protect the wiring, wrap

adhesive tape around them where they lie

against metal parts.

31. Rear speaker

— Place all cables away from moving parts, such

as gear shift and seat rails.

— Place all cables away from hot places, such as

near the heater outlet.

— Do not pass the yellow cable through a hole

32. Subwoofer

into the engine compartment to connect to a

battery.

— Cover any disconnected cable connectors with

insulating tape.

— Do not shorten any cables.

— Never cut the insulation of the power cable of

27. Power amp

this unit in order to share the power to other

(sold separately)

equipment. Current capacity of the cable is

limited.

— Use a fuse of the rating prescribed.

— Never wire the speaker negative cable directly

to ground.

— Never band together multiple speaker's

negative cables.

36. Rear speaker

or subwoofer

English

Connecting the units

Connection Diagram

• Control signal is output through blue/white cable

when this unit is powered on. Connect it to an

1. This product

external power amp's system remote control or

2. Rear output or subwoofer output

the vehicle's auto-antenna relay control terminal

(max. 300 mA, 12 V DC). If the vehicle is equipped

(DEH-3200UB)

with a glass antenna, connect it to the antenna

3. Rear output (DEH-4200SD)

booster power supply terminal.

4. Front output (DEH-4200SD)

• Never connect blue/white cable to external power

5. Subwoofer output (DEH-4200SD)

amp's power terminal. Also, never connect

6. Wired remote input

it to the power terminal of the auto antenna.

Hard-wired remote control adaptor can be

Otherwise, battery drain or malfunction may

connected (sold separately).

result.

• Black cable is ground. This cable and other

7. Fuse (10 A)

product's ground cable (especially, high-current

8. Antenna jack

products such as power amp) must be wired

9. Notes

separately. Otherwise, fire or malfunction may

• Change the initial setting of this unit (refer

result if they are accidentally detached.

to the operation manual). The subwoofer

output of this unit is monaural

(DEH-3200UD).

• When using a subwoofer of 70 W (2 Ω), be

sure to connect with Violet and Violet/black

leads of this unit. Do not connect anything

with Green and Green/black leads.

10. Note

Depending on the kind of vehicle, the function

of 2* and 4* may be different. In this case, be

sure to connect 1* to 4* and 3* to 2*.

11. Speaker leads

White: Front left

White/black: Front left

Gray: Front right

Gray/black: Front right

Green: Rear left

or subwoofer

Green/black: Rear left

Violet: Rear right

Violet/black: Rear right

12. Connect leads of the same color to each other.

13. Yellow (2*)

Back-up (or accessory)

14. Yellow (1*)

Connect to the constant 12 V supply terminal.

15. Red (4*)

Accessory (or back-up)

16. Red (3*)

Connect to terminal controlled by ignition

switch (12 V DC).

17. Black (chassis ground)

Connect to a clean, paint-free metal location.

18. ISO connector

Note

In some vehicles, the ISO connector may

be divided into two. In this case, be sure to

connect to both connectors.

English

19. Yellow/black

If you use an equipment with Mute function,

wire this lead to the Audio Mute lead on that

equipment. If not, keep the Audio Mute lead

free of any connections.

20. Blue/white

Connect to system control terminal of the

power amp (max. 300 mA 12 V DC).

21. Blue/white (6*)

Connect to auto-antenna relay control terminal

(max. 300 mA 12 V DC).

22. Blue/white (5*)

The pin position of the ISO connector will differ

depending on the type of vehicle. Connect 5*

and 6* when Pin 5 is an antenna control type.

In another type of vehicle, never connect 5*

and 6*.

23. For DEH-4200SD

24. To subwoofer output

25. To rear output

26. To front output

27. Power amp (sold separately)

28. Connect with RCA cables (sold separately)

29. System remote control

30. Front speaker

31. Rear speaker

32. Subwoofer

33. Perform these connections when using the

optional amplifier.

34. For DEH-3200UB

or subwoofer

35. To rear output or subwoofer output

or subwoofer

36. Rear speaker or subwoofer

or subwoofer

37. Connect with RCA cable (sold separately)