Pioneer Super Tuner IIID DVH-P5000MP Panduan Instalasi

Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Penerima Mobil Pioneer Super Tuner IIID DVH-P5000MP. Pioneer Super Tuner IIID DVH-P5000MP 8 halaman. 2004 mobile entertainment systems
Juga untuk Pioneer Super Tuner IIID DVH-P5000MP: Panduan Pemilik (34 halaman), Panduan Pengguna (24 halaman), Panduan Pengoperasian (4 halaman)

Halaman Cetak

DVH-P5000MP

This product conforms to CEMA cord colors.

Le code de couleur des câbles utilisé pour ce produit est con-

forme à CEMA.

Printed in Japan

Imprimé au Japon

<CRD3792-A> UC

Connecting the Units

• Speakers connected to this unit must be high-

Notes

power types with minimum rating of 50 W and

• This unit is for vehicles with a 12-volt battery

impedance of 4 to 8 ohms. Connecting speak-

and negative grounding. Before installing it in

ers with output and/or impedance values other

a recreational vehicle, truck, or bus, check the

than those noted here may result in the speak-

battery voltage.

ers catching fire, emitting smoke, or becoming

• To avoid shorts in the electrical system, be

damaged.

sure to disconnect the ≠ battery cable before

• When this product's source is switched ON, a

beginning installation.

control signal is output through the blue/white

• Refer to the owner's manual for details on

lead. Connect to an external power amp's sys-

connecting the power amp and other units,

tem remote control or the car's Auto-antenna

then make connections correctly.

relay control terminal (max. 300 mA 12 V DC).

• Secure the wiring with cable clamps or adhe-

If the car features a glass antenna, connect to

sive tape. To protect the wiring, wrap adhesive

the antenna booster power supply terminal.

tape around them where they lie against metal

• When an external power amp is being used

parts.

with this system, be sure not to connect the

• Route and secure all wiring so it cannot touch

blue/white lead to the amp's power terminal.

any moving parts, such as the gear shift, hand-

Likewise, do not connect the blue/white lead to

brake, and seat rails. Do not route wiring in

the power terminal of the auto-antenna. Such

places that get hot, such as near the heater

connection could cause excessive current

outlet. If the insulation of the wiring melts or

drain and malfunction.

gets torn, there is a danger of the wiring short-

• To avoid short-circuiting, cover the discon-

circuiting to the vehicle body.

nected lead with insulating tape. Especially,

• Don't pass the yellow lead through a hole into

insulate the unused speaker leads without fail.

the engine compartment to connect to the

There is a possibility of short-circuiting if the

battery. This will damage the lead insulation

leads are not insulated.

and cause a very dangerous short.

• To prevent incorrect connection, the input side

• Do not shorten any leads. If you do, the protec-

of the IP-BUS connector is blue, and the out-

tion circuit may fail to work when it should.

put side is black. Connect the connectors of

• Never feed power to other equipment by cut-

the same colors correctly.

ting the insulation of the power supply lead of

the unit and tapping into the lead. The current

capacity of the lead will be exceeded, causing

overheating.

• When replacing fuse, be sure to use only fuse

of the rating prescribed on this unit.

• Since a unique BPTL circuit is employed, never

wire so the speaker leads are directly

grounded or the left and right ≠ speaker leads

are common.

Connecting the Units

• If this unit is installed in a vehicle that does not

have an ACC (accessory) position on the igni-

tion switch, the red lead of the unit should be

connected to a terminal coupled with ignition

switch ON/OFF operations. If this is not done,

the vehicle battery may be drained when you

are away from the vehicle for several hours.

(Fig. 1)

ACC position

No ACC position

Fig. 1

• The black lead is ground. Please ground this

lead separately from the ground of high-cur-

rent products such as power amps.

If you ground the products together and the

ground becomes detached, there is a risk of

damage to the products or fire.

• Cords for this product and those for other

products may be different colors even if they

have the same function. When connecting this

product to another product, refer to the sup-

plied Installation manuals of both products

and connect cords that have the same func-

tion.