Ariston PH 941MSTV Panduan Petunjuk Pengoperasian - Halaman 3
Jelajahi secara online atau unduh pdf Panduan Petunjuk Pengoperasian untuk Kompor Ariston PH 941MSTV. Ariston PH 941MSTV 13 halaman. Built-in cooking table
Juga untuk Ariston PH 941MSTV: Petunjuk Instalasi dan Penggunaan Manual (13 halaman), Spesifikasi (13 halaman), Panduan Instalasi dan Penggunaan (34 halaman), Panduan Petunjuk Pengoperasian (20 halaman)
Halaman Cetak
Hooking position
for top H=40 mm
! Use the hooks contained in the "accessory pack"
• Where the hob is not installed over a built-in oven, a
wooden panel must be installed as insulation. This
must be placed at a minimum distance of 20 mm from
the lower part of the hob.
Ventilation
To ensure adequate ventilation, the back panel of the
cabinet must be removed. It is advisable to install the
oven so that it rests on two strips of wood, or on a
completely flat surface with an opening of at least 45 x
560 mm ( see diagrams ).
When installing on a built-in oven without forced
ventilation, ensure that there are air inlets and outlets for
ventilating the interior of the cabinet adequately.
Electrical connection
Hobs equipped with a three-pole power supply
cable are designed to operate with alternating
current at the voltage and frequency indicated on
the data plate (this is located on the lower part of the
appliance). The earth wire in the cable has a green
and yellow cover. If the appliance is to be installed
above a built-in electric oven, the electrical
connection of the hob and the oven must be carried
out separately, both for electrical safety purposes
and to make extracting the oven easier.
Front
Back
Connecting the supply cable to the mains
Install a standardised plug corresponding to the
load indicated on the data plate.
The appliance must be directly connected to the
mains using an omnipolar circuit-breaker with a
minimum contact opening of 3 mm installed between
the appliance and the mains. The circuit-breaker
must be suitable for the charge indicated and must
comply with current electrical regulations (the earthing
wire must not be interrupted by the circuit-breaker).
The supply cable must not come into contact with
surfaces with temperatures higher than 50°C.
! The installer must ensure that the correct electrical
connection has been made and that it is compliant
with safety regulations.
Before connecting to the power supply, make sure
that:
• The appliance is earthed and the plug is
compliant with the law.
• The socket can withstand the maximum power of
the appliance, which is indicated on the data
plate.
• The voltage is in the range between the values
indicated on the data plate.
• The socket is compatible with the plug of the
appliance. If the socket is incompatible with the
plug, ask an authorised technician to replace it.
Do not use extension cords or multiple sockets.
! Once the appliance has been installed, the power
supply cable and the electrical socket must be
easily accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced
by authorised technicians only ( see Assistance ).
! The manufacturer declines any liability should
these safety measures not be observed.
Gas connection
The appliance should be connected to the main gas
supply or to a gas cylinder in compliance with
current national regulations. Before carrying out the
connection, make sure the cooker is compatible with
the gas supply you wish to use. If this is not the
case, follow the instructions indicated in the
paragraph "Adapting to different types of gas."
When using liquid gas from a cylinder, install a
pressure regulator which complies with current
national regulations.
! Check that the pressure of the gas supply is
consistent with the values indicated in Table 1
("Burner and nozzle specifications"). This will ensure
the safe operation and longevity of your appliance
while maintaining efficient energy consumption.
GB
3