Ariston PH 941MSTV 사용 설명서 - 페이지 3

{카테고리_이름} Ariston PH 941MSTV에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Ariston PH 941MSTV 13 페이지. Built-in cooking table
Ariston PH 941MSTV에 대해서도 마찬가지입니다: 설치 및 사용 설명서 지침 (13 페이지), 사양 (13 페이지), 설치 및 사용 설명서 (34 페이지), 사용 설명서 (20 페이지)

페이지 인쇄

Hooking position

for top H=40 mm

! Use the hooks contained in the "accessory pack"

• Where the hob is not installed over a built-in oven, a

wooden panel must be installed as insulation. This

must be placed at a minimum distance of 20 mm from

the lower part of the hob.

Ventilation

To ensure adequate ventilation, the back panel of the

cabinet must be removed. It is advisable to install the

oven so that it rests on two strips of wood, or on a

completely flat surface with an opening of at least 45 x

560 mm ( see diagrams ).

When installing on a built-in oven without forced

ventilation, ensure that there are air inlets and outlets for

ventilating the interior of the cabinet adequately.

Electrical connection

Hobs equipped with a three-pole power supply

cable are designed to operate with alternating

current at the voltage and frequency indicated on

the data plate (this is located on the lower part of the

appliance). The earth wire in the cable has a green

and yellow cover. If the appliance is to be installed

above a built-in electric oven, the electrical

connection of the hob and the oven must be carried

out separately, both for electrical safety purposes

and to make extracting the oven easier.

Front

Back

Connecting the supply cable to the mains

Install a standardised plug corresponding to the

load indicated on the data plate.

The appliance must be directly connected to the

mains using an omnipolar circuit-breaker with a

minimum contact opening of 3 mm installed between

the appliance and the mains. The circuit-breaker

must be suitable for the charge indicated and must

comply with current electrical regulations (the earthing

wire must not be interrupted by the circuit-breaker).

The supply cable must not come into contact with

surfaces with temperatures higher than 50°C.

! The installer must ensure that the correct electrical

connection has been made and that it is compliant

with safety regulations.

Before connecting to the power supply, make sure

that:

• The appliance is earthed and the plug is

compliant with the law.

• The socket can withstand the maximum power of

the appliance, which is indicated on the data

plate.

• The voltage is in the range between the values

indicated on the data plate.

• The socket is compatible with the plug of the

appliance. If the socket is incompatible with the

plug, ask an authorised technician to replace it.

Do not use extension cords or multiple sockets.

! Once the appliance has been installed, the power

supply cable and the electrical socket must be

easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced

by authorised technicians only ( see Assistance ).

! The manufacturer declines any liability should

these safety measures not be observed.

Gas connection

The appliance should be connected to the main gas

supply or to a gas cylinder in compliance with

current national regulations. Before carrying out the

connection, make sure the cooker is compatible with

the gas supply you wish to use. If this is not the

case, follow the instructions indicated in the

paragraph "Adapting to different types of gas."

When using liquid gas from a cylinder, install a

pressure regulator which complies with current

national regulations.

! Check that the pressure of the gas supply is

consistent with the values indicated in Table 1

("Burner and nozzle specifications"). This will ensure

the safe operation and longevity of your appliance

while maintaining efficient energy consumption.