Whirlpool Cabrio,- WED7300X Penggunaan & Perawatan Gude - Halaman 19

Halaman Cetak

Whirlpool Cabrio,- WED7300X Penggunaan & Perawatan Gude

Troubleshooting

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help -

If you experience

Washer not performing as expected (cont.)

Incorrect dispenser

operation

Powdered detergent not

dissolving completely in

load

Single-dose laundry

packet not dissolving

Error Code Appears in Display

F#E# code (F-type error

code) appears in display

F8E1 or LF (too long to

fill) appears in display

F9E1, drn, dr (drain

pump system problem

- long drain) appears in

display

F8E6 (Lid opened)

appears in display

F1E1 ACU (Appliance

control fault)

F2E5 UI/ACU mismatch

F3E1 Water level sensing

failure

F5E2 Lid lock will not

lock or lid lock failure

F5E3 Lid cannot unlock

F6E2 or F6E3

Communication Error:

UI cannot communicate

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

Possible Causes

Clogged dispensers or laundry

products dispensing too soon.

Liquid chlorine bleach not used in

dispenser.

Using too much HE detergent.

Water temperature is very cold.

Adding laundry packet incorrectly.

System error code.

Washer taking too long to fill. Drain

extends more than 4.5" (114 mm) into

standpipe.

Washer taking too long to drain

water. Drain extends more than

4.5" (114 mm) into standpipe.

Washer lid left open.

Internal ACU failure.

Wrong ACU or UI has been installed.

Pressure sensor on ACU failure.

An item in the load maybe keeping

the lid from locking.

Objects on washer lid keep it from

unlocking.

ACU or UI synchronization error.

Do not overfill dispenser. Overfilling causes immediate dispensing.

Load dispensers before starting a cycle.

It is normal for small amounts of water to be remain in dispenser

at the end of the cycle.

Fabric softener thickens as it gets older. If there becomes an

increase of fabric softener in the dispenser after a cycle, then

check the age of the fabric softener and replace if needed.

Homes with low water pressure may result in residual powder

in the dispenser. To avoid, select a warmer wash temperature

if possible, depending on your load.

Use only liquid chlorine bleach in the bleach dispenser.

Follow the manufacturer's instructions to determine the amount

of detergent to use.

Select a warmer wash temperature.

Try adding the detergent to the basket prior to adding laundry,

rather than using the detergent dispenser.

Be sure laundry packet is added to washer basket before adding

clothes. Follow the manufacturer's instructions to avoid damage

to your items.

Touch POWER to clear the code and exit cycle. Then touch

POWER, select cycle, and then touch and hold START/PAUSE to

start washer. If code appears again, call for service.

Check plumbing for correct drain hose installation. Use drain

hose form and attach securely to drainpipe or tub. Do not tape

over drain opening. See Installation Instructions.

Make sure water supply line is turned on.

Check plumbing for correct drain hose installation. Use drain

hose form and attach securely to drainpipe or tub. Do not tape

over drain opening.

Lower drain hose if the end is higher than 96" (2.4 m) above

the floor. Remove any clogs from drain hose. See Installation

Instructions.

Close the lid and touch Power to clear the display. If the lid is left

open for more than 10 minutes, the cycle will reset and water in

the washer will drain.

Call for service.

Check for items directly under the lid.

Remove objects, such as baskets of laundry, from top of washer.

Remove power from the washer. Let washer set for 5 minutes for

the washer to completely power down. Apply power to washer

and check for error codes. If the error code persists call for

service.

Solution