Whirlpool YGEW9250PL0 Panduan Penggunaan & Perawatan - Halaman 17

Jelajahi secara online atau unduh pdf Panduan Penggunaan & Perawatan untuk Pengering Whirlpool YGEW9250PL0. Whirlpool YGEW9250PL0 40 halaman. Electronic electric dryer

Halaman Cetak

From Inside the Dryer Cabinet

Lint should be removed every 2 years or more often, depending

on dryer usage. Cleaning should be done by a qualified person.

From the Exhaust Vent

Lint should be removed every 2 years, or more often, depending

on dryer usage.

Vacation

care

Operate your dryer only when you are at home. If you will be on

vacation or not using your dryer for an extended period of time,

you should:

1. Unplug dryer or disconnect

power.

2. Clean lint screen. See "Cleaning the Lint Screen."

Moving care

Emectricat Shock Hazard

Disconnect

power before servicing.

Replace aH parts and panels before operating.

Failure to do so can resuJt in death or emectrical shock.

1. Unplug dryer or disconnect

power. Disconnect

wiring if dryer

is direct wired.

2. Make sure leveling legs are secure in dryer base.

3. Use masking tape to secure dryer door.

The dryer light automatically turns on inside the dryer drum when

you open the door.

To change the drum light

1. Unplug dryer or disconnect

power.

2. Open the dryer door. Locate the light bulb cover on the back

wall of the dryer. Remove the screw located in the lower right

corner of the cover. Remove the cover.

3. Turn bulb counterclockwise.

Replace the bulb with a 10-watt

appliance bulb only. Replace the cover and secure with the

screw.

4. Plug in dryer or reconnect power.

TROUBLESHOOTING

First try the solutions suggested

here and possibly avoid

the cost of a service call...

Dryer displaying

code message

•

"PF" (power failure), check the following:

Was the drying cycle interrupted

by a power failure?

Press (and hold) HOLD TO START button to restart the dryer.

•

"E" Variable (El, E2, E3) service codes:

Call for service.

Clothes

are not drying satisfactorily

•

Checkthe

following:

Is the lint screen clogged with lint?

Is the exhaust vent or outside exhaust hood clogged with lint,

restricting air movement? Run the dryer for 5-10 minutes.

Hold your hand under the outside exhaust hood to check air

movement.

If you do not feel air movement, clean exhaust

system of lint or replace exhaust vent with heavy metal or

flexible metal vent. See "Installation

Instructions."

Is the exhaust vent crushed or kinked? Replace with a heavy

metal or flexible metal vent. See "Installation

Instructions."

Has a fuse blown, or has a circuit breaker tripped? Electric

dryers use 2 household fuses or breakers. The drum may be

turning, but you may not have heat.

Has an air cycle been selected? Select the right cycle for the

types of garments being dried. See "Cycles."

Is the automatic cycle ending early? The load may not be

contacting

the electronic sensor strips. Level the dryer.

Are fabric softener sheets blocking the grille? Use only one

fabric softener sheet and only use it once.

Is the dryer located in a room with temperature

below

45°F (7°C)?

Proper operation of dryer cycles requires temperatures

above

45°F (7°C).

•

Was a cold rinse water used? Was the load very wet?

Expect longer drying times with items rinsed in cold water

and with items that hold moisture (cottons).

•

Is the load too large and heavy to dry quickly?

Separate the load to tumble freely.

Dryer will not run

•

Check the following:

Is the power cord plugged in?

Has a fuse blown, or has a circuit breaker tripped?

Was a regular fuse used? Use a time-delay fuse.

Is the dryer door firmly closed? If not, the time display will

blink.

Was HOLD TO START firmly pressed and held for at least

1 second?

Is a cycle selected?