Important: Observe all governing codes
and ordinances.
Proper installation
is your responsibility.
A qualified
technician must install this range. Make sure you
have everything necessary for correct installation. It
is the installer's responsibility
to comply with
installation clearances specified on the model/serial
rating plate. The model/serial rating plate is located
on the oven frame behind the oven door.
Check location where range will be installed. The
range should be located for convenient use in
kitchen.
ALL OPENINGS IN THE WALL OR FLOOR WHERE
RANGE IS TO BE INSTALLED MUST BE SEALED.
Cabinet opening dimensions that are shown must
be used. Given dimensions are minimum
clearances.
Grounded electrical outlet is required. See
"Electrical requirements,"
Page 2.
Electrical Shock Hazard
It is the customer's responsibility
to contact
a qualified electrical installer; and to make sure
that the electrical installation
is adequate and in
conformance with National Electrical Code,
ANSUNFPA 70 - latest edition*, and all local
codes and ordinances.
Failure to do so could result in death or serious
injury.
Injury Hazard
To eliminate the risk of burns or fire, avoid
installing cabinet storage above the cooking
surface. If cabinets are already installed, reduce
the hazard of reaching over a heated cooking
surface by installing a range hood. The range
hood should extend a minimum of 5 inches out
from the bottom front of the cabinets.
Reaching over a heated cooking surface
could result in a serious burn or other injury.
Mobile home installation
The installation of this range must conform with the
Manufactured Home Construction and Safety
Standard, Title 24 CFR, Part 3280 [formerly the
Federal Standard for Mobile Home Construction
and Safety, Title 24, HUD (Part 28011 or, when such
standard is not applicable, the Standard for
Manufactured
Home Installations, ANSI
A225.1/NFPA 501A, or with local codes.
When this range is installed in a mobile home, it
must be secured to the floor during transit. Any
method of securing the range is adequate as long
as it conforms to the standards listed above.
Four-wire power supply cable must be used in a
mobile home installation. The appliance wiring will
need to be revised. See four-wire electrical
connection, Page 3.
Copies of the standards
listed may be obtained
from:
l
National
Fire Protection
Association
Batterymarch
Park
Quincy,
Massachusetts
02269
Anti-tip bracket
The floor mounted anti-tip bracket or an optional tether kit
MUST be installed. To install the anti-tip bracket shipped
with the range, see Page 2 and the anti-tip bracket
template/instruction
sheet. If this bracket cannot be used,
a wall-mounted
anti-tip tether kit, Part No. 814234, is
available from your dealer.
For minimum
clearance, to the top
of the cooktop see
!
a
4" min.
countertop
space to side
wall or other
combustible
material
I
Wall receptacle -
(1
8" to 22" from
either cabinet. 7"
1 p
max.fromflo&
ctis
by l/2"
**Note: 24" min. when bottom of wood or metal
cabinet is protected by not less than l/4" flame
retardant millboard covered with not less than
No. 28 MSG sheet steel, 0.015" stainless steel,
0.024" aluminum or 0.020" copper.
30" min. clearance between the top of the
cooking platform and the bottom of an
unprotected
wood or metal cabinet.
Do Not pinch the power
supply cord between the
range and the wall.
Do Not seal the range to
the side cabinets.
I Oven frame must extend
screwdriver
or
5/16" nut driver
lu" adjustable
3/8" nut
P
,.
9
wren nch
driver
""
3/E" socket wrench
with 7/16" socket
r==?%?, measuring
I
3 tape or ruler
4%
A
'
w
-,-
glasses
wood floor
l/8" drill bit
concrete/ceramic
floor
3/16" carbide-tipped
masonry drill bit
astic
hors
2 screws Ml0 x l-
Brackets must be securely mounted to sub-floor. Thickness of
flooring may require longer screws to anchor bracket to sub-
floor. Longer screws are available from your local hardware
store.
Page 1
Halaman Cetak