Xerox M123 WorkCentre Panduan Pengaturan Jaringan Cepat - Halaman 4

Jelajahi secara online atau unduh pdf Panduan Pengaturan Jaringan Cepat untuk Mesin fotokopi Xerox M123 WorkCentre. Xerox M123 WorkCentre 7 halaman. Stand installation guide
Juga untuk Xerox M123 WorkCentre: Panduan Instalasi (2 halaman), Panduan Evaluator (12 halaman), Brosur & Spesifikasi (6 halaman), Instal Manual (2 halaman), Manual Jaringan (50 halaman), Manual Pemindaian (28 halaman), Kartu Instalasi Cepat (2 halaman), Manual (28 halaman), Panduan Instalasi Office Finisher (6 halaman), Panduan Instalasi Office Finisher (6 halaman), Panduan Pemasangan Perangkat Keras (4 halaman), Panduan Pemasangan Baki Berkapasitas Tinggi (3 halaman), Panduan Pemasangan Baki Berkapasitas Tinggi (3 halaman), Panduan Pemasangan Kit Hard Drive (2 halaman), Panduan Instalasi Inverter (2 halaman), Panduan Instalasi (2 halaman), Panduan Pemasangan Perangkat Keras (2 halaman), Manual Pemasangan Dudukan (2 halaman), Panduan Referensi (20 halaman), Panduan Servis (22 halaman)

Halaman Cetak
Xerox M123 WorkCentre Panduan Pengaturan Jaringan Cepat
Q
u
i
c
k
N
e
t
w
Q
u
i
c
k
N
e
t
w
For WorkCentre M123/M128 WorkCentre Pro 123/128
The System Administrator Guide contains detailed information about Network setups. This
document is intended for setting up the Network using TCP/IP. If using Novell IPX, then see the
System Administrator Guide for setup procedures
Pre-requisites for quick Network Setup using TCP/IP:
1. Confirm that an existing operational network utilizing TCP/IP is available.
2. Confirm that the Ethernet cable is plugged into the M123/M128 and into an operational
Ethernet port on the network.
NOTE:
The Ethernet cable is an RJ45 type and is not supplied by Xerox
Configuring M123/M128 IP address via DHCP:
On startup, the M123/M128 Multifunction device defaults to DHCP to obtain its network
configurations. A DHCP server delivers an IP address as well as other configuration settings to
the device. If you use a DHCP server to allocate an IP address to the M123/M128 device, then
proceed as follows:
Procedure for quick Network Setup using TCP/IP:
Step 1:
Power on the M123/M128 device
Step 2:
Wait a minute or so while the M123/M128 device negotiates an IP address. Then print
out the Network Connectivity Page
To print the Network Configuration Report:
1. Select the Machine Status button on the M123/M128
2. Select Print Report List
3. Select Print Mode Settings
4. Select Setting List – Common Items
5. Press the Start button.
The Network Connectivity Page will be printed. Read the details to confirm that an IP address
has been allocated and that is a valid IP address on your network.
N
OTE:
If the IP address on the Connectivity report starts with 167.xxx.xxx.xxx, then the DHCP
server has not properly allocated an address or DHCP is not enabled on your network.
Step 3
: Record the IP address allocated and from a workstation, open up a web browser (such
as
Internet Explorer).
123/M128 device IP address). If connected properly, you will see the M123/M128 device's
CentreWare Internet Services web page (see below).
QNS
o
r
k
S
e
t
u
p
(
D
o
r
k
S
e
t
u
p
(
D
.
.
Type in the URL
Page 4 of 7
H
C
P
)
H
C
P
)
.
http://xxx.xxx.xxx.xxx
(The xxx's represent the
701P42078