Xerox M123 WorkCentre 빠른 네트워크 설정 매뉴얼 - 페이지 4

{카테고리_이름} Xerox M123 WorkCentre에 대한 빠른 네트워크 설정 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Xerox M123 WorkCentre 7 페이지. Stand installation guide
Xerox M123 WorkCentre에 대해서도 마찬가지입니다: 설치 매뉴얼 (2 페이지), 평가자 매뉴얼 (12 페이지), 브로셔 및 사양 (6 페이지), 설치 매뉴얼 (2 페이지), 네트워크 매뉴얼 (50 페이지), 스캔 매뉴얼 (28 페이지), 빠른 설치 카드 (2 페이지), 매뉴얼 (28 페이지), Office 피니셔 설치 매뉴얼 (6 페이지), Office 피니셔 설치 매뉴얼 (6 페이지), 하드웨어 설치 매뉴얼 (4 페이지), 대용량 트레이 설치 매뉴얼 (3 페이지), 대용량 트레이 설치 매뉴얼 (3 페이지), 하드 드라이브 키트 설치 매뉴얼 (2 페이지), 인버터 설치 매뉴얼 (2 페이지), 설치 매뉴얼 (2 페이지), 하드웨어 설치 매뉴얼 (2 페이지), 스탠드 설치 매뉴얼 (2 페이지), 참조 매뉴얼 (20 페이지), 서비스 매뉴얼 (22 페이지)

페이지 인쇄
Xerox M123 WorkCentre 빠른 네트워크 설정 매뉴얼
Q
u
i
c
k
N
e
t
w
Q
u
i
c
k
N
e
t
w
For WorkCentre M123/M128 WorkCentre Pro 123/128
The System Administrator Guide contains detailed information about Network setups. This
document is intended for setting up the Network using TCP/IP. If using Novell IPX, then see the
System Administrator Guide for setup procedures
Pre-requisites for quick Network Setup using TCP/IP:
1. Confirm that an existing operational network utilizing TCP/IP is available.
2. Confirm that the Ethernet cable is plugged into the M123/M128 and into an operational
Ethernet port on the network.
NOTE:
The Ethernet cable is an RJ45 type and is not supplied by Xerox
Configuring M123/M128 IP address via DHCP:
On startup, the M123/M128 Multifunction device defaults to DHCP to obtain its network
configurations. A DHCP server delivers an IP address as well as other configuration settings to
the device. If you use a DHCP server to allocate an IP address to the M123/M128 device, then
proceed as follows:
Procedure for quick Network Setup using TCP/IP:
Step 1:
Power on the M123/M128 device
Step 2:
Wait a minute or so while the M123/M128 device negotiates an IP address. Then print
out the Network Connectivity Page
To print the Network Configuration Report:
1. Select the Machine Status button on the M123/M128
2. Select Print Report List
3. Select Print Mode Settings
4. Select Setting List – Common Items
5. Press the Start button.
The Network Connectivity Page will be printed. Read the details to confirm that an IP address
has been allocated and that is a valid IP address on your network.
N
OTE:
If the IP address on the Connectivity report starts with 167.xxx.xxx.xxx, then the DHCP
server has not properly allocated an address or DHCP is not enabled on your network.
Step 3
: Record the IP address allocated and from a workstation, open up a web browser (such
as
Internet Explorer).
123/M128 device IP address). If connected properly, you will see the M123/M128 device's
CentreWare Internet Services web page (see below).
QNS
o
r
k
S
e
t
u
p
(
D
o
r
k
S
e
t
u
p
(
D
.
.
Type in the URL
Page 4 of 7
H
C
P
)
H
C
P
)
.
http://xxx.xxx.xxx.xxx
(The xxx's represent the
701P42078