Directed Directechs DB3 Panduan Instalasi - Halaman 4

Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Alarm Mobil Directed Directechs DB3. Directed Directechs DB3 18 halaman. Smart key for 2013 toyota highlander
Juga untuk Directed Directechs DB3: Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Manual (6 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (10 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (10 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman), Panduan Instalasi (19 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (17 halaman), Panduan Instalasi (20 halaman), Panduan Instalasi (18 halaman)

Directed Directechs DB3 Panduan Instalasi

Pre-installation and application warnings

This section highlights important information for this specific firmware and will assist in pricing accordingly, as
START
HERE
well as bringing awareness to any operational or vehicle limitations.
Compatibilities and Requirements
T-Harness
.
compatible
Vehicle Takeover
Firmware notes
OEM Remote Starter:
Š
starter and disable it. If the vehicle is equipped with an OEM remote starter, whether Active or Inactive, it MUST be temporarily
disabled or permanently disconnected depending on the vehicle. Please refer to the "OEM remote starter information" section of the
guide for additional details.
Note: In some cases, the module will program to the vehicle even if equipped with an OEM starter, but will prevent the aftermarket
remote
start from functioning properly.
Keyless and Smart Key: will remain functional during remote start.
Š
All connectors are displayed from the wire side (unless specified otherwise).
Š
Refer to the "Vehicle connections" following the installation diagram.
Š
Footnotes
[1] Hood pin: The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin or if
not supported in data.
[2] Tach wire: This is an optional connection required on some remote starters, which do not support a tach signal in D2D. Also, by
default, the tach is set to 1000 rpm on hybrid vehicles
[3] Pit Stop/Idle mode: This connection is only required for Pit Stop/Idle mode in manual transmission vehicles.
[4] Autolights: This connection is only required if vehicle is equipped with autolights..
4
403.TL6 2.26 2018 Toyota RAV4 Hybrid (Smart Key)
©2023 Directed. All rights reserved.
T-Harness is not compatible.
Takeover feature is not available on Push-to-Start vehicles. Engine will shut off when door is opened.
Before programming your module, you must first check if your vehicle is equipped with an OEM remote
Keys
1
Keys required
required for
for operation
programming
0