Directed Directechs DB3 Kurulum Kılavuzu - Sayfa 4

Araba Alarmı Directed Directechs DB3 için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Directed Directechs DB3 18 sayfaları. Smart key for 2013 toyota highlander
Ayrıca Directed Directechs DB3 için: Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (19 sayfalar), Manuel (6 sayfalar), Kurulum Kılavuzu (18 sayfalar), Kurulum Kılavuzu (18 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (10 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (10 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (18 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (18 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (18 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (18 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (17 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (18 sayfalar)

Sayfayı Yazdır

Directed Directechs DB3 Kurulum Kılavuzu

Pre-installation and application warnings

This section highlights important information for this specific firmware and will assist in pricing accordingly, as

START

HERE

well as bringing awareness to any operational or vehicle limitations.

Compatibilities and Requirements

T-Harness

compatible

Vehicle Takeover

Firmware notes

OEM Remote Starter:

starter and disable it. If the vehicle is equipped with an OEM remote starter, whether Active or Inactive, it MUST be temporarily

disabled or permanently disconnected depending on the vehicle. Please refer to the "OEM remote starter information" section of the

guide for additional details.

Note: In some cases, the module will program to the vehicle even if equipped with an OEM starter, but will prevent the aftermarket

remote

start from functioning properly.

Keyless and Smart Key: will remain functional during remote start.

All connectors are displayed from the wire side (unless specified otherwise).

Refer to the "Vehicle connections" following the installation diagram.

Footnotes

[1] Hood pin: The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin or if

not supported in data.

[2] Tach wire: This is an optional connection required on some remote starters, which do not support a tach signal in D2D. Also, by

default, the tach is set to 1000 rpm on hybrid vehicles

[3] Pit Stop/Idle mode: This connection is only required for Pit Stop/Idle mode in manual transmission vehicles.

[4] Autolights: This connection is only required if vehicle is equipped with autolights..

403.TL6 2.26 2018 Toyota RAV4 Hybrid (Smart Key)

T-Harness is not compatible.

Takeover feature is not available on Push-to-Start vehicles. Engine will shut off when door is opened.

Before programming your module, you must first check if your vehicle is equipped with an OEM remote

Keys

Keys required

required for

for operation

programming