Zanussi FJE 1207 Panduan Pengguna - Halaman 11

Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Mesin cuci Zanussi FJE 1207. Zanussi FJE 1207 23 halaman. Zanussi washer user manual
Juga untuk Zanussi FJE 1207: Panduan Pengguna (24 halaman)

Halaman Cetak

At the end of the cycle, the light of the START/

PAUSE button

will flash and the programme

phase indicator light

will remain lit to indicate that

the water must be drained.

To complete the cycle, choose one of the following

options:

• Draining and spin:

- Press the START/PAUSE button. The machine

will drain the water, then spin the laundry at the

maximum speed provided for the selected

programme.

Select spin speed by means of button 5, and

press the START/PAUSE button.

• Drain only

- Press the RESET button

cause the DRAIN light

the START/PAUSE button.

Important! If you accidentally press the RESET

button more than once, the memory will be

cleared. To drain the water, select any washing

programme by means of the FABRIC button

then press RESET three times in order to select

the DRAIN position (only the DRAIN light

remain lit).

6 SOIL DEGREE button

This button allows you to select the suitable washing

for your laundry.

= normally soiled laundry.

The machine automatically proposes this

position when you select the programme/

fabric.

= heavy soiled laundry.

Only for cotton and synthetic fabrics. The

washing phase will be prolonged by approx.

10 minutes.

= Slightly soiled laundry.

The washing time will be reduced according to

the type of fabric and the selected

temperature.

Not for wool/hand wash

7 OPTIONS button

Press this button to select the following options:

• PREWASH

: select this option if you wish your

laundry to be prewashed before the main wash

(not available for wool/hand wash and quick

wash).

The prewash ends with a short spin in programmes

for cotton and synthetic fabrics, whereas in the

programme for delicate fabrics the water is only

once, so as to

to light up, then press

will

and quick wash

drained.

• BIO: this function can be selected for cotton and

synthetics with a washing temperature of 40° or

more degrees.

The machine will maintain a temperature of 40° for

about 10 minutes to enable the enzymes contained

in the detergent to eliminate the dirt.

To be used for laundry with "stubborn" stains.

8 START/PAUSE button

This button has three functions:

• Start: after you have selected the desired

programme and options, press this button to start

the washing machine. The light above the button

will stop flashing and remain lit.

• Pause: when you press this button again, the

programme in progress is interrupted. The light

above the button will start flashing. To restart the

programme, press the button again.

When you PAUSE the cycle, the DOOR LOCKED

light goes out, and it becomes possible to open the

door, provided

• the washing machine is not in the heating phase;

• the level of the water is not high;

• the drum is not turning.

Important! You must set the washing machine to

PAUSE before you make any change in the

programme in progress.

• Draining of water and spinning after the

execution of programmes with the RINSE HOLD

option

9 RESET button

At the end of a programme, you must press this

button once or repeatedly, in order to clear the

contents of the memory; the programme phase

indicator lights must be off, otherwise, the next time

you switch the washing machine on, the audible

warning signals relevant to the end of the previous

cycle will be given.

You can also press the RESET button to exclude

one or several phases of the programme which is

running, as indicated below.

- set the washing machine to PAUSE by pressing the

START/PAUSE button (the relevant light will flash);

- press the RESET button once or several

times, until the required phase(s) is(are) cancelled

(the light next to the name of the phase(s) will go out).