Clarus Fusion Series Panduan Pemilik - Halaman 4

Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Sistem Penyaringan Air Clarus Fusion Series. Clarus Fusion Series 20 halaman. Treatment systems
Juga untuk Clarus Fusion Series: Panduan Pemilik (20 halaman)

Halaman Cetak

DATAPLATE

A dataplate similar to the one in Figure 5 is located on the blower

housing and the alarm panel. There is important information about

the Fusion

on the dataplate, such as the part number, model

number, serial number, and hydraulic capacity. Please make a note

of this information for future reference or in case you should need to

contact your Fusion

maintenance provider.

The contracting installer must mark the installed model number on

the dataplate, the blower housing and the alarm control panel.

ALARM PANEL

The Fusion

utilizes an alarm panel (see Figure 6) that is designed to

activate an audible buzzer and red beacon light on top of the panel if

there is a drop in air pressure, if a high water alarm condition occurs,

or if the blower does not cycle between recirculation and backwash

modes within the preset time. (Note: Alarm panel can only function

as long as there is electrical power supplied to the panel)

You may from time to time check the proper operation of the alarm

panel by toggling the black switch on the side of the panel to "test".

The buzzer will sound and the red beacon will light as long as you

hold the switch in the test position. Release the switch for normal

operation.

SYSTEM CARE

The Fusion

system is designed to continuously operate automatically with

little direct maintenance from the owner. Periodically, a check of the blower

area is recommended to ensure no debris obstructs the ventilation or intake

areas of the blower. Also, periodically test the control panel as outlined under

the alarm panel section. The owner should closely monitor the types and

amounts of substances and products used. Water use should also be closely

monitored to ensure proper operation of the Fusion

Periodically, more extensive maintenance must be performed. Your authorized

Fusion

maintenance provider will oversee this service. The name of the

maintenance provider can be recorded on the front of this document and should

also be located on the alarm panel. For more information see the Operation and

Maintenance section of the manual.

The owner should only perform minimal routine maintenance on the Fusion

such as clearing debris from around blower housing (leaves, snow, and grass

clippings). The Fusion

should also be protected from excessive weight such

as vehicular traffic. Trees and bushes should not be planted in close proximity

to the Fusion

. The Fusion

should be accessible to maintenance personnel

and the riser lids must never be buried.

HIGH USE WATER DEVICES

The draining of hot tubs and swimming pools into your Fusion

will cause hydraulic overloading and will impair the treatment efficiency.

Please drain these devices to another location. Contact your local

regulatory authorities or authorized Fusion

more information. The use of large capacity single fill and drain whirlpool

bathtubs may also cause hydraulic overloading of your Fusion

the use of these types of tubs.

FLOODING

If flooding of the Fusion

alarm panel is submerged, please disconnect power at the circuit breaker.

DO NOT try to reconnect power to either the blower or alarm panel once

it has been submerged. Immediately contact your authorized Fusion

maintenance provider to inspect the Fusion

panel. Your maintenance provider will repair or replace the components as

needed.

system.

system

maintenance provider for

. Please limit

occurs and the blower or the

, the blower, and the alarm

Figure 5

F U S IO N TRE ATM EN T SY ST EM

□

ZF 450

□

ZF 800

MFG．DATE：

Manufacturer:

Clarus Environmental • 3649 Cane Run Road

Louisville, KY 40211 • 1-800-928-7867

B LO WER SER V I ＣE P ART S

COMPLETE BLOWER:

BLOWER DIAPHRAGM:

BLOWER FILTER:

Figure 6

FUSION

DATAPLATE

Figure 7

120 VAC L1

INCOMING N

POWER GND

BLOWER

BLOWER FOR ZF-450 AND ZF-800

LEAKY FIXTURES

It is very important to monitor all water fixtures in the home for leaks and

*FOR ILLUSTRATION PURPOSES ONLY*

drips and repair them immediately. Leaks can cause tremendous water

use and may hydraulically overload your Fusion

its treatment efficiency. Excessive water use may also overload your soil

absorption field and cause failure.

INTERMITTENT USE

The Fusion

system is designed to function even if wastewater does not

enter it for extended periods of time. The power to the blower must remain

on during this time for the system to function properly. Weekend use will

not harm the system as long as the blower is on. Should seasonal use

require a complete shut down of the property, then it is recommended that

the blower be turned off. It is important to start up the system in advance of

actual occupancy to allow for normal treatment to resume. Please contact

your authorized Fusion

maintenance provider for further information

concerning shut down and startup of the Fusion

your maintenance provider for the shut down and startup services.

450 GALLONS/DAY

800 GALLONS/DAY

Certified to

NSF - ANSI

Standard 40

toll free

P/N 5250-0050-A

P/N 152949-A

P/N 152950-A

RED BEACON

WARNING!

SILENCE/TEST

SWITCH

P/N

BUZZER

1 2 3 4 5 6 7 8

TB2

DISNF

ALARM

HIGH WATER

ALARM

REFER TO SCHEMATIC LOCATED IN

system and reduce

PANEL FOR INSTALLATION

. You may also contact

sk2649

GND LUG

sk2933