Dixon 6200X Petunjuk Pemasangan & Pengoperasian - Halaman 2
Jelajahi secara online atau unduh pdf Petunjuk Pemasangan & Pengoperasian untuk Peralatan Industri Dixon 6200X. Dixon 6200X 4 halaman. Bayco tall drop elbows
Halaman CetakIMPORTANT: This elbow is designed for use with standard 4" top seal service
station adapters. To properly operate and maintain your BAYCO
6200X series elbow the following instructions are provided. Please
read with care as improper handling or maintenance may cause a
hazardous condition.
CAUTION: Do not modify your BAYCO 6200X 6500X series elbow for any
reason. It can result in a hazardous condition due to operating
difficulties or operation malfunction. Disassembly or tampering will void
the product warranty.
Never smoke or allow an open flame near your dispenser when
handling volatile materials such as gasoline and fuels. An explosion
could result. Remember safety is everyone's business.
Installation: When the Bayco 6200X / 6500X elbow is shipped, the sight glass
and gaskets are attached in a plastic bag attached to the elbow. These
must be installed with the required mating Bayco inlet (3" or 4" male or
female purchased separately). Take the sight glass and gaskets out of
the plastic bag and place one gasket inside the elbow inlet end and
make sure it is sealed evenly. Carefully (keep straight) slide the sight
glass into the inlet end and onto the installed gasket. Place the other
gasket inside the inlet and on the sight glass. Attach the mating inlet
using the four socket head cap screws supplied. Coat the cap screws
with anti-seize compound.
Lubricate Stem: This product has been assembled with anti-seize compound
and lubricated for easy maintenance and trouble-free service. However,
we recommend lubricating the stem through the grease nipple using
lithium based or quality automotive type grease prior to service. It is
recommended to apply lubricant to grease nipple, cam arm bearings,
and other moving parts every month. Monthly inspection and lubrication
become mandatory for items that are seldom used. Condensation, rain
and road salts can cause corrosion build-up and binding when product
not in use.
Check Operation: Place elbow bottom end on service station adapter (elbow
is designed for use with 4" top seal adapter only). Move operators
handle to 11 o'clock the open/unclamped position. Release and hold the
safety latch if equipped with one.
o'clock position for full clamping (lever cannot be moved any farther).
Check locking arms on adapter. If the elbow is fitted with a safety latch,
make sure the stem pin is in the latch notch, preventing movement of
operating handle. Release by moving handle to 11 o'clock. If fitted with
safety latch, lift the latch lever and operating lever at the same time.
Move the handle clockwise to 2
Care & Handling: Bayco drop elbows are tested at the factory and are in
proper working condition when shipped. Drop elbows are designed to
be tough and to provide long service with reasonable care and
handling. To ensure long service Bayco elbows should not be thrown,
dropped or dragged; such actions may compromise the integrity and
reduce the service life of the product.
Inspect for Damage: Drop elbows can fail to operate if not properly
maintained. If the 6200X / 6500X elbow develops any problems,
remove from service and contact your Bayco distributor describing the
difficulty. The distributor will provide further instructions repair and
warranty of the product. Elbows should be inspected monthly.
Check the main gasket seal, the sight glass, and the flange where the
base is attached to the elbow body for any signs of leakage. Change
seals if necessary. Check the sight glass for cracks or damage and
replace if needed.
Check and tighten all fasteners periodically.
Lubricate the lever stem. Check the bushings and replace if cracked
or worn, and change if required. Check operation as per above.
Regularly Replace Bushings: All Bayco 6200 / 6400 / 6500 series elbows
contain polymer bushings, which protect and extend service life of
bronze locking arms. The bushings are designed to wear (instead of
bronze arms) and should be replaced every few months. Operators
must be encouraged to inspect and replace polymer bushings to
obtain maximum elbow performance and longevity.
Optional Accessories: The following are available as optional accessories
for #6200X / 6500X elbows;
Anti-spill sleeve #6200X-17
Safety latch kit #6200SLK.
Installation instructions are included with the items when ordered for
retrofit.
DIXON BAYCO WARRANTY: For complete warranty information, please
refer to the inside back cover of the latest Dixon catalogue.
090086 R6