Dixon 6200X Istruzioni per l'installazione e il funzionamento - Pagina 2

Sfoglia online o scarica il pdf Istruzioni per l'installazione e il funzionamento per Apparecchiature industriali Dixon 6200X. Dixon 6200X 4. Bayco tall drop elbows

Stampa la pagina

IMPORTANT: This elbow is designed for use with standard 4" top seal service

station adapters. To properly operate and maintain your BAYCO

6200X series elbow the following instructions are provided. Please

read with care as improper handling or maintenance may cause a

hazardous condition.

CAUTION: Do not modify your BAYCO 6200X 6500X series elbow for any

reason. It can result in a hazardous condition due to operating

difficulties or operation malfunction. Disassembly or tampering will void

the product warranty.

Never smoke or allow an open flame near your dispenser when

handling volatile materials such as gasoline and fuels. An explosion

could result. Remember safety is everyone's business.

Installation: When the Bayco 6200X / 6500X elbow is shipped, the sight glass

and gaskets are attached in a plastic bag attached to the elbow. These

must be installed with the required mating Bayco inlet (3" or 4" male or

female purchased separately). Take the sight glass and gaskets out of

the plastic bag and place one gasket inside the elbow inlet end and

make sure it is sealed evenly. Carefully (keep straight) slide the sight

glass into the inlet end and onto the installed gasket. Place the other

gasket inside the inlet and on the sight glass. Attach the mating inlet

using the four socket head cap screws supplied. Coat the cap screws

with anti-seize compound.

Lubricate Stem: This product has been assembled with anti-seize compound

and lubricated for easy maintenance and trouble-free service. However,

we recommend lubricating the stem through the grease nipple using

lithium based or quality automotive type grease prior to service. It is

recommended to apply lubricant to grease nipple, cam arm bearings,

and other moving parts every month. Monthly inspection and lubrication

become mandatory for items that are seldom used. Condensation, rain

and road salts can cause corrosion build-up and binding when product

not in use.

Check Operation: Place elbow bottom end on service station adapter (elbow

is designed for use with 4" top seal adapter only). Move operators

handle to 11 o'clock the open/unclamped position. Release and hold the

safety latch if equipped with one.

o'clock position for full clamping (lever cannot be moved any farther).

Check locking arms on adapter. If the elbow is fitted with a safety latch,

make sure the stem pin is in the latch notch, preventing movement of

operating handle. Release by moving handle to 11 o'clock. If fitted with

safety latch, lift the latch lever and operating lever at the same time.

Move the handle clockwise to 2

Care & Handling: Bayco drop elbows are tested at the factory and are in

proper working condition when shipped. Drop elbows are designed to

be tough and to provide long service with reasonable care and

handling. To ensure long service Bayco elbows should not be thrown,

dropped or dragged; such actions may compromise the integrity and

reduce the service life of the product.

Inspect for Damage: Drop elbows can fail to operate if not properly

maintained. If the 6200X / 6500X elbow develops any problems,

remove from service and contact your Bayco distributor describing the

difficulty. The distributor will provide further instructions repair and

warranty of the product. Elbows should be inspected monthly.

Check the main gasket seal, the sight glass, and the flange where the

base is attached to the elbow body for any signs of leakage. Change

seals if necessary. Check the sight glass for cracks or damage and

replace if needed.

Check and tighten all fasteners periodically.

Lubricate the lever stem. Check the bushings and replace if cracked

or worn, and change if required. Check operation as per above.

Regularly Replace Bushings: All Bayco 6200 / 6400 / 6500 series elbows

contain polymer bushings, which protect and extend service life of

bronze locking arms. The bushings are designed to wear (instead of

bronze arms) and should be replaced every few months. Operators

must be encouraged to inspect and replace polymer bushings to

obtain maximum elbow performance and longevity.

Optional Accessories: The following are available as optional accessories

for #6200X / 6500X elbows;

Anti-spill sleeve #6200X-17

Safety latch kit #6200SLK.

Installation instructions are included with the items when ordered for

retrofit.

DIXON BAYCO WARRANTY: For complete warranty information, please

refer to the inside back cover of the latest Dixon catalogue.

090086 R6