djm direct 01985-V2 Manual Petunjuk Asli - Halaman 4
Jelajahi secara online atau unduh pdf Manual Petunjuk Asli untuk Melihat djm direct 01985-V2. djm direct 01985-V2 17 halaman.
Halaman Cetakf) Dress properly. Do not wear loose clothing or jewellery. Keep
your hair, clothing and gloves away from moving parts. Loose
clothes, jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly used.
Use of dust collection can reduce dust-related hazards.
5.4 Power tool use and care
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at
the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and
off. Any power tool that cannot be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery
pack from the power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not
allow persons unfamiliar with the power tool or these instructions
to operate the power tool. Power tools are dangerous in the hands
of untrained users.
e) Maintain power tools. Check for misalignment or binding of
moving parts, breakage of parts and any other condition that may
affect the power tool's operation. If damaged, have the power tool
repaired before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting
tools with sharp cutting edges are less likely to bind and are easier to
control.
g) Use the power tool, accessories and tool bits etc. in accordance
with these instructions, taking into account the working conditions
and the work to be performed. Use of the power tool for operations
different from those intended could result in a hazardous situation.
5.5 Service
a) Have your power tool serviced by a qualified repair person using
only identical replacement parts. This will ensure that the safety of
the power tool is maintained.
b) If the replacement of the supply cord is necessary, this has to be
done by the manufacturer or its agent in order to avoid a safety
hazard.
6 Safety instructions for table saws
6.1 Guarding related Warnings
a) Keep guards in place. Guards must be in working order and be
properly mounted. A guard that is loose, damaged, or is not
functioning correctly must be repaired or replaced.
b) Always use a saw blade guard and riving knife for every
through-cutting operation. For through-cutting operations where
the saw blade cuts completely throught the thickness of the
workpiece, the guard and other safety devices help reduce the risk of
injury.
c) After completing working procedures where the removal of the
blade guard and/or riving knife is necessary(e.g. rebating, cutting
grooves or other procedures where the workpiece needs to be
turned over), the guard must be reattached immediately. The guard
helps to reduce the risk of injury.
d) Make sure the saw blade is not touching the guard, riving knife or
the workpiece before the switch is turned on. Inadvertent contact of
these items with the saw blade could cause a hazardous condition.
e) Adjust the riving knife as described in this instruction manual.
Incorrect spacing, positioning and alignment can make the riving
knife ineffective in reducing the likelihood of kickback.
f) For the riving knife to work, it must be engaged in the workpicece.
The riving knife is ineffective when cutting workipieces that are too
short to be engaged with the riving knife. Under these conditions a
kickback cannot be prevented by the riving knife.
g) Use the appropriate saw blade for the riving knife. For the riving
knife to function properly, the saw blade diameter must match the
appropriate riving knife and the body of the saw blade must be
thinner than the thickness of the riving knife
6.2 Cutting procedure warnings
a) Danger: Never place your hands and fingers in the sawing area or
close to the saw blade. A moment of carelessness or a slip could
steer your hand towards the saw blade and result in serious
injuries.
b) Feed the workpiece into the saw blade only against the direction
of rotation. Feeding the workpiece in the same direction as the saw
blade is roating above the table may lead to the workpiece and
your hand being drawn into the saw blade.
C) Never use the mitre gauge to feed the workpiece when ripping
and do not use the rip fence as a length stop when cross cutting
with the mitre gauge. Guiding the workpiece with the rip fence and
the mitre gauge at the same time increases the likelihood of saw
blade binding and kickback.
d) When ripping, always apply the workpiece feeding force between
the fence and the saw blade. Use a push stick when the distance
between the fence and the saw blade is less than 150mm, and use a
push block when this distance is less than 50mm. These working
3