Alula RE614-Au Panduan Memulai Cepat - Halaman 8

Jelajahi secara online atau unduh pdf Panduan Memulai Cepat untuk Alarm Asap Alula RE614-Au. Alula RE614-Au 13 halaman. Smoke alarm connect+ encrypted

Halaman Cetak

Figure 7c

Figure 7d

SELF TAPPING

Attach the Alarm to the mounting plate.

Line up the screw (not supplied) on the "U"

shaped recessed area shown in Figure 7c and

screw firmly home.

To remove the Alarm from the ceiling,

remove the screw first, and then twist off

anti-clockwise.

7. Testing, Maintenance and

Power Supply Monitoring

Your Alarm is a life saving device and should be

checked periodically.

7.1 Manually Testing your Alarms

It is recommended that you test your Alarms

after installation and then at least weekly to

ensure the units are working. It will also help

you and your family to become familiar with

the sound of the Alarms.

- Press and hold the Test Button until the

Alarm sounds and the red light flashes (see

Figure 7). The Alarm will stop sounding shortly

after the button is released.

- Repeat this procedure for all other Alarms in

the system.

WARNING: Do not test with flame.

This can set fire to the Alarm and damage the

house. We do not recommend testing with

smoke as the results can be misleading unless

special apparatus is used.

When you press the Test button it simulates

the effect of smoke in a Smoke Alarm which it

could experience in a real fire.

7.2 Test/Silence Button to Control Nuisance

Alarms

The Smoke Alarms have a combined Test/

Silence button to help you control nuisance/

TAMPERPROOF SCREW

SCREW

2 to 3 mm

false alarms.

If, when the Alarm sounds, there is no sign of

smoke or noise to indicate that there is a fire,

it should be assumed that it is due to an actual

fire and the dwelling should be evacuated

immediately.

Check the house carefully in case there is a

small fire smouldering somewhere.

Check whether there is some source of smoke

or fumes, for example cooking fumes being

drawn past the Alarm by an extractor.

If there are frequent nuisance/false alarms

it may be necessary to re-locate the Smoke

Alarm away from the source of the fumes.

1. To cancel a false alarm from a Smoke Alarm

(which has its red light flashing rapidly), press

the Test/Silence button (the Smoke Alarm will

automatically switch to a reduced sensitivity

condition).

The Smoke Alarms will be silenced for a period

of approximately 10 minutes. The red light on

the cover of the Smoke Alarm will flash every

8 seconds to indicate that the unit has been

silenced.

2. The Smoke Alarm will reset to normal

sensitivity at the end of the silenced period

(10 minutes). If additional silenced time is

required, simply push the Test/Silence button

again.

3. If kitchen usage/layout is such that there

are an unacceptable level of nuisance alarms,

re-locate the Smoke Alarm further away where

it will be less affected by cooking fumes etc.

We recommend the use of a Heat Alarm in the

Kitchen area to avoid such nuisance alarms.

7.3 Power Supply Monitoring

7.3.1 What to do when an Alarm is beeping:

A Smoke Alarm is beeping about every 48

seconds with the yellow light flashing at the

same time:

- The battery contained in the smoke alarm is

low. Replace the entire smoke alarm.

Dispose of used smoke alarm promptly. Keep

away from children. Do not disassemble and

do not dispose of in fire

7.4 Cleaning your Alarm

Clean your Alarm regularly. Use a soft bristle

brush or the brush attachment of your vacuum

cleaner to remove dust and cobwebs from the

side slots where the smoke enters. To clean

the cover, wipe with a damp cloth and dry

thoroughly.

WARNING: Do not paint your Alarm.

Other than the maintenance and cleaning

described in this leaflet, no other customer

servicing of this product is required. Repairs,