Alutech LM-L Panduan Pengoperasian - Halaman 2

Jelajahi secara online atau unduh pdf Panduan Pengoperasian untuk Aksesori Alutech LM-L. Alutech LM-L 2 halaman. Photocells
Juga untuk Alutech LM-L: Panduan Pengoperasian (2 halaman)

Halaman Cetak

Operating

manual

PHOTOCELLS

LM-L

ENGLISH

DESCRIPTION

The photocells are designated to warn of any foreign objects on

the optical axis between the transmitter (TX) and the receiver (RX)

of the photocells.

DELIVERY SCOPE

Transmitter (TX) .......................................................................................................... 1 pc.

Receiver (RX) ................................................................................................................ 1 pc.

Manual ............................................................................................................................. 1 pc.

Dowel with screw .......................................................................................................8 ps.

TECHNICAL SPECIFICATIONS

Supply voltage ............................................................................ 12 V ... 24 V AC / DC

Transmitter (TX) consumption ...................................................................≤ 15 mА

Receiver (RX) consumption .........................................................................≤ 30 mА

Range .................................................................................................not less than 12 m

Positioning accuracy ..................................................................................................± 5 °

Output relay contacts load ...................................................... 1 А / max 30 V DC

Output contacts type .............................................................................. NC and NO

Infrared wave length .........................................................................................940 nm

Housing protection class ......................................................................................IP 54

Working temperature range ....................................................− 20 º С ... + 60 º С

Measurements............................................................... 90 mm × 55 mm × 27 mm

Connection cable cross-section ........................... max 1 mm2 (AWG16-26)

Display ....................................................................................................... LED in receiver

The company reserves the right to make changes to this

manual and technical specifications of the product without

prior notice. The content of this manual cannot form the basis

for legal claims.

Transmitter TX

A C - D C

1 2 -2 4 V

Рис. / Мал. / Fig. 1

Перед началом монтажа фотоэлементов, необходимо их разо-

брать, а затем монтировать в следующем порядке:

Перед початком монтажу фотоелементів потрібно їх розібрати,

а потім монтувати в такому порядку:

Before mounting the photocells, they should be disassembled, and

then assembled in the following order:

1. Установить основание

Встановити основу

Fit the base

Рис. / Мал. / Fig. 2

INSTALLATION AND CONNECTION

Only qualified specialists can install and connect the product

in compliance with the regulatory documentation in force and

following the applicable safety procedures.

Before making any connections, check that the automation

to which photocells are connected is disconnected from the

mains and from the batteries, in case of accidental activation.

Before mounting the photocells select the location for the trans-

mitter and receiver and place them on one level at height of not

more than 20 cm and endure they are facing one another in a di-

rect line. The distance between transmitter and receiver should

not exceed 50 cm. Check that the selected mounting places are

protected from impacts and the mounting surfaces are strong

enough. Lay the cables to the transmitter and receiver mounting

places beforehand.

When mounting, fasten the transmitter first and connect electric

cables (see diagram), then align (center) and connection the re-

ceiver. The photocells are connected and aligned correctly, if the

receiver LED is not illuminated, and when crossing the optical ray

the LED illuminates and relay switching is heard. Check the LED

operation several times.

Due to possible reflections of infrared rays from the floor,

walls, objects etc. the photocells should be checked and used

only with their lids installed b, which serve as filters for cut-

ting the visible light and containing the lenses which focus

(is lit when active)

the rays. Protect the photocells receiver from direct sun light.

The installation and connection drawings are shown on fig. 1–6.

Receiver RX

LE D

2. Прикрутить плату к основанию

Прикрутити плату до основи

A C -D C

Screw the board to the base

1 2 -2 4 V

C O M

N O

N C

POW ER

OU TPU T

Рис. / Мал. / Fig. 3

3. Подключить провода

Підключити проводи

Connect wires

Рис. / Мал. / Fig. 4

STORAGE, TRANSPORTATION

AND DISPOSAL

Keep the packed product in dry premises at temperatures between

of 0 ... + 25 ° С and relative air humidity no more than 80 %. The air

inside the premises must not contain acidic, alkaline and other ag-

gressive substances. Do not expose the product to the precipitation

or direct sunlight. Storage period—3 years from the date of manu-

facture. Transportation may be carried out by means of any roofed

land vehicle fitted with the means to prevent crushing of packages

and load retention equipment.

Disposal is to be performed in accordance with the

current waste processing and disposal regulations ap-

plicable in the country of the Customer. The product

does not contain precious metals and substances that

pose a threat to life, human health or the environment.

Operation life—5 years.

WARRANTY

The warranty on the operation capacity of the product is provided if

the storage, transportation and maintenance operations are carried

out according to the set regulations. The warranty period is three

years. Under the warranty, the service department only eliminates

malfunctions caused by the fault of the Manufacturer.

Note: the parts replaced under the warranty are considered the pro-

perty of the service department that carried out the product repair.

The warranty does not apply in the following cases:

•

violation of use and storage regulations;

•

alterations performed by unauthorised persons, damage of the

products caused by the consumer or third parties;

•

damage caused by water ingression within the device;

•

force majeure (fires, lightning strikes, floods, earthquakes and

other natural disasters);

•

failure to provide a completed operation manual.

For questions about the service please contact the organization

that carried out the installation of the equipment.

STATEMENT OF COMPLIANCE

Copies of declarations of compliance can be found at:

http://www.alutech-group.com/en/products/other/automatics/

documents

Made in China

Manufacturer: 'Hangzhou Hiland Technology Co., Ltd'

4th Building, 2 Xiyuanwu Road, Westlake Technology Garden,

Hangzhou, China +86 571 81958376

Importer to the Republic of Belarus / Authorised representa-

tive: Alutech Systems s.r.o., 348 02, Czech Republic, Bor u Tachova,

CTPark Bor, Nova Hospoda 19, D5-EXIT 128,

phone / fax: + 420 374 6340 01,

e-mail: [email protected]

4. Прикрутить среднюю часть фотоэлемента

Прикрутити середню частину фотоелемента

Screw the middle part of the photocell

Рис. / Мал. / Fig. 5

5. Закрыть светофильтром

Закрити світлофільтром

Cover with light-filter

Рис. / Мал. / Fig. 6