American Standard Towel Bar 6724 Istruzioni per l'installazione

Sfoglia online o scarica il pdf Istruzioni per l'installazione per Arredamento per interni American Standard Towel Bar 6724. American Standard Towel Bar 6724 2. 18" towel bar 24" towel bar

Stampa la pagina
American Standard Towel Bar 6724 Istruzioni per l'installazione
STANDARD
COLLECTION
18" TOWEL BAR
24" TOWEL BAR
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Recommended Tools
10'
Tape Measure
1
18" and 24" TOWEL BAR
The 18" TOWEL BAR (1) and 24' TOWEL BAR (2) work best if secured to a wall stud or cross brace within the wall,
using the SCREWS (3) supplied.
If the 18" TOWEL BAR (1) and 24' TOWEL BAR (2) is to be installed on a tile or plaster wall the TILE ANCHORS (4) or
DRYWALL ANCHORS (6) and SCREWS (3) should be used.
Determine desired height and location (optional) and mark a center line. For the 24" TOWEL BAR (2) mark a centerline 24" horizontally
from the first location. For the 18" TOWEL BAR (1) mark a centerline 18" from the first location. Using the MOUNTING PLATE (5) as a
template mark the two mounting holes. Repeat for the other MOUNTING PLATE (5). If MOUNTING PLATE (5) is secured to a stud or
cross brace, drill small pilot holes for SCREWS (4).
For installations on drywall, use DRYWALL ANCHORS (6) and SCREWS (3) for securing MOUNTING PLATE (5) to wall. Place #2 Phillips
screwdriver or cordless screwdriver into recess of anchor. Press into drywall while turning the anchor clockwise until it is seated flush with
the wall. Place MOUNTING PLATE (5) over DRYWALL ANCHORS (6) and insert SCREWS (3) with #2 Phillips screwdriver. See illustration
below. Secure MOUNTING PLATE (5) to wall with SCREWS (3).
For installations on tiled walls, If TILE ANCHORS (4) and SCREWS (3) are used for securing MOUNTING PLATE (5), then drill two
1/4" diameter holes a minimum of 1-1/4" deep. Insert the two TILE ANCHORS (4) flush with face of the finished wall. Secure
MOUNTING PLATE (5) to wall with SCREWS (3).
Install the WALL ESCUTCHEON (7) on the MOUNTING PLATE (5). Place the 18" TOWEL BAR (1) and 24' TOWEL BAR (2) into the
SIDE SUPPORT BRACKET (10, 10a). Align slot in towel bar with notch in recess of support post (10, 10a) (see Figure A). Place the18"
TOWEL BAR (1) and 24' TOWEL BAR (2) on the ESCUTCHEON (7) and MOUNTING BRACKET (5). Secure with MOUNTING SCREW (8).
Tighten fully.
Push INDEX BUTTONS (9) into SIDE SUPPORT BRACKET (10, 10a). See illustration.
4
6
5
3
CENTER LINE
18"
Instructions
Regular Screwdriver
Drill
Phillips Screwdriver
USE MOUNTING PLATE
AS TEMPLATE
CENTER
LINE
48 TO 72
INCHES FROM
FLOOR
6
4
24"
48" TO 60"
(OPTIONAL)
Installation
6718
6724
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR
WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID,
POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH
WITH A COARSE SURFACE.
3
4
5
FINISHED
WALL
Certified to comply with ANSI A112.18.1
U.S. Patent No. D403,750
7
8
9
10
10a
SLOT IN TOWEL BAR
Figure A
NOTCH IN RECESS OF SUPPORT POST
M 9 6 8 2 1 7 B
1
2