American Standard Towel Bar 6724 Installation Instructions

Browse online or download pdf Installation Instructions for Indoor Furnishing American Standard Towel Bar 6724. American Standard Towel Bar 6724 2 pages. 18" towel bar 24" towel bar

Print Page

STANDARD

COLLECTION

18" TOWEL BAR

24" TOWEL BAR

Thank you for selecting American-Standard...the benchmark

of fine quality for over 100 years.

To ensure that your installation proceeds smoothly--please

read these instructions carefully before you begin.

Recommended Tools

10'

Tape Measure

18" and 24" TOWEL BAR

The 18" TOWEL BAR (1) and 24' TOWEL BAR (2) work best if secured to a wall stud or cross brace within the wall,

using the SCREWS (3) supplied.

If the 18" TOWEL BAR (1) and 24' TOWEL BAR (2) is to be installed on a tile or plaster wall the TILE ANCHORS (4) or

DRYWALL ANCHORS (6) and SCREWS (3) should be used.

Determine desired height and location (optional) and mark a center line. For the 24" TOWEL BAR (2) mark a centerline 24" horizontally

from the first location. For the 18" TOWEL BAR (1) mark a centerline 18" from the first location. Using the MOUNTING PLATE (5) as a

template mark the two mounting holes. Repeat for the other MOUNTING PLATE (5). If MOUNTING PLATE (5) is secured to a stud or

cross brace, drill small pilot holes for SCREWS (4).

For installations on drywall, use DRYWALL ANCHORS (6) and SCREWS (3) for securing MOUNTING PLATE (5) to wall. Place #2 Phillips

screwdriver or cordless screwdriver into recess of anchor. Press into drywall while turning the anchor clockwise until it is seated flush with

the wall. Place MOUNTING PLATE (5) over DRYWALL ANCHORS (6) and insert SCREWS (3) with #2 Phillips screwdriver. See illustration

below. Secure MOUNTING PLATE (5) to wall with SCREWS (3).

For installations on tiled walls, If TILE ANCHORS (4) and SCREWS (3) are used for securing MOUNTING PLATE (5), then drill two

1/4" diameter holes a minimum of 1-1/4" deep. Insert the two TILE ANCHORS (4) flush with face of the finished wall. Secure

MOUNTING PLATE (5) to wall with SCREWS (3).

Install the WALL ESCUTCHEON (7) on the MOUNTING PLATE (5). Place the 18" TOWEL BAR (1) and 24' TOWEL BAR (2) into the

SIDE SUPPORT BRACKET (10, 10a). Align slot in towel bar with notch in recess of support post (10, 10a) (see Figure A). Place the18"

TOWEL BAR (1) and 24' TOWEL BAR (2) on the ESCUTCHEON (7) and MOUNTING BRACKET (5). Secure with MOUNTING SCREW (8).

Tighten fully.

Push INDEX BUTTONS (9) into SIDE SUPPORT BRACKET (10, 10a). See illustration.

CENTER LINE

18"

Instructions

Regular Screwdriver

Drill

Phillips Screwdriver

USE MOUNTING PLATE

AS TEMPLATE

CENTER

LINE

48 TO 72

INCHES FROM

FLOOR

24"

48" TO 60"

(OPTIONAL)

Installation

6718

6724

CARE INSTRUCTIONS:

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR

WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.

DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID,

POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH

WITH A COARSE SURFACE.

FINISHED

WALL

Certified to comply with ANSI A112.18.1

U.S. Patent No. D403,750

10a

SLOT IN TOWEL BAR

Figure A

NOTCH IN RECESS OF SUPPORT POST

M 9 6 8 2 1 7 B