Alemlube 670AN3 Manuale tecnico del proprietario - Pagina 6

Sfoglia online o scarica il pdf Manuale tecnico del proprietario per Strumenti Alemlube 670AN3. Alemlube 670AN3 8. 18v cordless grease gun 450g

Alemlube 670AN3 Manuale tecnico del proprietario
SER 595-A
 
 

Specific Safety Rules

 
 
WARNING
 
The gun can develop high pressure up to
8,000 psi (552 bar). Rupture of components can
inject grease into skin and eyes, causing serious
injury and possible amputation. If injured, seek
immediate medical attention.
 
Do not operate without proper safety protection,
gloves, and goggles. Hold hose at spring guard
only. Do not use if hose is damaged or worn.
Inspect hose before each use. Use only Alemite
340067 Grease Whip Hose.
 
This gun uses lubricants, that may be flammable
and poisonous if ingested. Do not use gun near
open flame or other fire hazards. Read all
warnings on lubricants before using this gun.
 
Use ear protection to reduce the risk of induced
hearing loss.
 
Disconnect battery pack from gun before changing
accessories or storing the gun.
 
 
 
Warning! To reduce the risk of inj ury, the
user must read the instruction manual.
 
 
Separate collection. This product must not be
disposed of with normal household waste.
 
Loading and Priming the Gun
 
NOTE: Refer to Figure 2 for component
identification on the following procedures.
 
Cartridge Loading
 
1. Unscrew Grease Cylinder (30) from the gun.
 
2. Pull the follower rod and engage the groove in the
follower rod with the slot in the Grease Cylinder cap.
 
3. Remove the plastic cap from the cartridge.
 
4. Apply a film of grease to the exposed inside surface of
the cartridge.
 
NOTE: This is only necessary for a virgin
gun.
 
5. Insert the cartridge into the Grease Cylinder.
• Remove the tabbed seal from the cartridge.
 
6. Screw the Grease Cylinder onto the gun.
 
7. Disengage the follower rod from the slot in the Grease
Cylinder cap.
• Push the follower rod into the Grease Cylinder.
 
Revision (10-11)
NSW
TEL: (02) 9677 1555
FAX: (02) 9675 1155
QLD/PNG
VIC/TAS
TEL: (07) 3204 9166
TEL: (03) 8787 8288
FAX: (07) 3204 1224
FAX: (03) 8787 8266
Visit our website at
www.alemlube.com.au
Suction Loading
 
1. Unscrew Grease Cylinder (30) from gun.
 
2. Insert the head of the Grease Cylinder below the
surface of the grease.
 
3. Slowly pull the follower rod outward from the Grease
Cylinder cap until the groove is visible.
 
4. Engage the groove in the follower rod with the slot in
the Grease Cylinder's cap.
 
5. Screw the Grease Cylinder onto the gun.
 
6. Disengage the follower rod from the slot in the Grease
Cylinder cap.
• Push the follower rod into the Grease Cylinder.
 
Loader Pump
WARNING
 
The gun can be equipped with an optional
low-pressure Loader Fitting. Do not substitute with
a high-pressure grease fitting. Personal injury can
occur due to excessive pressure.
 
The use of a grease fitting will void the warranty.
 
 
 
CAUTION
 
The Loader Fitting on the gun must mate with the
loader coupler. The pump may not operate if the
components are not compatible.
 
 
1. Pull the follower rod and engage the follower by
rotating the rod.
 
2. Seat the Loader Fitting into the loader coupler.
• Push down to hold the coupler valve open.
 
3. Operate the pump and view the movement of the
follower rod.
 
4. Discontinue pump operation once the groove on the
follower rod is visible.
 
5. Disengage follower rod from follower and push into
the Grease Cylinder.
6
WA
TEL: (08) 9302 4199
FAX: (08) 9303 2095
or
www.alemlube.co.nz
Cordless Grease Gun
Alemite, LLC
SA/NT
NZ
TEL: (08) 8241 7111
TEL: (09) 447 1007
FAX: (08) 8241 7011
FAX: (09) 447 1008