Alemlube 670AN3 소유자 기술 매뉴얼 - 페이지 6

{카테고리_이름} Alemlube 670AN3에 대한 소유자 기술 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Alemlube 670AN3 8 페이지. 18v cordless grease gun 450g

페이지 인쇄

SER 595-A

Specific Safety Rules

WARNING

The gun can develop high pressure up to

8,000 psi (552 bar). Rupture of components can

inject grease into skin and eyes, causing serious

injury and possible amputation. If injured, seek

immediate medical attention.

Do not operate without proper safety protection,

gloves, and goggles. Hold hose at spring guard

only. Do not use if hose is damaged or worn.

Inspect hose before each use. Use only Alemite

340067 Grease Whip Hose.

This gun uses lubricants, that may be flammable

and poisonous if ingested. Do not use gun near

open flame or other fire hazards. Read all

warnings on lubricants before using this gun.

Use ear protection to reduce the risk of induced

hearing loss.

Disconnect battery pack from gun before changing

accessories or storing the gun.

Warning! To reduce the risk of inj ury, the

user must read the instruction manual.

Separate collection. This product must not be

disposed of with normal household waste.

Loading and Priming the Gun

NOTE: Refer to Figure 2 for component

identification on the following procedures.

Cartridge Loading

1. Unscrew Grease Cylinder (30) from the gun.

2. Pull the follower rod and engage the groove in the

follower rod with the slot in the Grease Cylinder cap.

3. Remove the plastic cap from the cartridge.

4. Apply a film of grease to the exposed inside surface of

the cartridge.

NOTE: This is only necessary for a virgin

gun.

5. Insert the cartridge into the Grease Cylinder.

• Remove the tabbed seal from the cartridge.

6. Screw the Grease Cylinder onto the gun.

7. Disengage the follower rod from the slot in the Grease

Cylinder cap.

• Push the follower rod into the Grease Cylinder.

Revision (10-11)

NSW

TEL: (02) 9677 1555

FAX: (02) 9675 1155

QLD/PNG

VIC/TAS

TEL: (07) 3204 9166

TEL: (03) 8787 8288

FAX: (07) 3204 1224

FAX: (03) 8787 8266

Visit our website at

www.alemlube.com.au

Suction Loading

1. Unscrew Grease Cylinder (30) from gun.

2. Insert the head of the Grease Cylinder below the

surface of the grease.

3. Slowly pull the follower rod outward from the Grease

Cylinder cap until the groove is visible.

4. Engage the groove in the follower rod with the slot in

the Grease Cylinder's cap.

5. Screw the Grease Cylinder onto the gun.

6. Disengage the follower rod from the slot in the Grease

Cylinder cap.

• Push the follower rod into the Grease Cylinder.

Loader Pump

WARNING

The gun can be equipped with an optional

low-pressure Loader Fitting. Do not substitute with

a high-pressure grease fitting. Personal injury can

occur due to excessive pressure.

The use of a grease fitting will void the warranty.

CAUTION

The Loader Fitting on the gun must mate with the

loader coupler. The pump may not operate if the

components are not compatible.

1. Pull the follower rod and engage the follower by

rotating the rod.

2. Seat the Loader Fitting into the loader coupler.

• Push down to hold the coupler valve open.

3. Operate the pump and view the movement of the

follower rod.

4. Discontinue pump operation once the groove on the

follower rod is visible.

5. Disengage follower rod from follower and push into

the Grease Cylinder.

TEL: (08) 9302 4199

FAX: (08) 9303 2095

www.alemlube.co.nz

Cordless Grease Gun

Alemite, LLC

SA/NT

TEL: (08) 8241 7111

TEL: (09) 447 1007

FAX: (08) 8241 7011

FAX: (09) 447 1008