Bosch 1614 Manuale di istruzioni - Pagina 6

Sfoglia online o scarica il pdf Manuale di istruzioni per Utensile elettrico Bosch 1614. Bosch 1614 28. Plunge router
Anche per Bosch 1614: Manuale di istruzioni (28 pagine)

Stampa la pagina
Bosch 1614 Manuale di istruzioni
Extension Cords
• Replace damaged cords immediately. Use of
damaged cords can shock, burn or electrocute.
• If an extension cord is necessary, a cord with
adequate size conductors should be used to
prevent excessive voltage drop, loss of power
or overheating. The table below shows the
correct size to use, depending on cord length
and amperage rating on the tool's nameplate. If
in doubt, use the next heavier gauge. Always
use U.L. and CSA listed extension cords.
Ampere Rating (shown on nameplate)
0-
2.1-
3.5-
2.0
3.4
5.0
25'
18
18
18
50'
18
18
16
75'
18
18
16
100'
18
16
14
150'
16
14
12
Note: The smaller the gauge number, the larger
the wire is in the cord.
"SAVE THESE INSTRUCTIONS"
Operating the Tool
Trigger Switch with "Lock-ON"button
Your tool can be turned "ON" or "OFF" by
squeezing or releasing the trigger. Your tool is
also equipped with "Lock-ON" button, located
on the left side of the trigger handle, that allows
for continuous operation without holding the
trigger.
TO LOCK SWITCH "ON": Squeeze trigger,
depress button and release trigger.
TO UNLOCK THE SWITCH: Squeeze trigger
and release it without depressing the "Lock-
ON" button.
WARNING!
If the "Lock-ON" button is con-
tinuously being depressed, the trigger cannot
be released.

BM 2610967928 1/97

Variable Speed with Dial Setting
Your router is also equipped with a variable
speed dial 2. The router bit speed can be preset
from 12,000 to maximum nameplate RPM by
rotating the dial to the desired setting. The dial
may be set on or between any of six positions (1
= low through 6 = high). The "Lock-ON"
button may also be used with any setting of the
dial.
The following speeds generally apply, but pre-
cise settings are largely determined by
experience with the material being cut. Mo-
mentary speed variation is normal when starting
the router until the electronic regulator takes
5.1-
7.1-
12.1-
control.
7.0
12.0
16.0
Dial 1613EVS 1614EVS
Setting
18
16
14
1
16
14
12
2
14
12
10
3
12
10
12 Wire Gauge
4
5
6
The router is equipped with the "soft start"
feature which gradually increases the starting
speed and torque, reducing the stress that oc-
curs from a high torque start.
Start the tool before applying to work and let
the tool come to full speed before contacting
the workpiece. Lift the tool from the work
before releasing the switch. DO NOT turn the
switch "ON" and "OFF" while the tool is under
load; this will greatly decrease the switch life.
Router Bit Installation and Removal
WARNING
from the power supply before installing router
bits, accessories or making any adjustments.
Turn the armature shaft to align the flats with
the spindle lock 11, and press the spindle lock
firmly down to engage it. Next, use the wrench
supplied to loosen the collet chuck assembly.
Insert the shank of the router bit into the collet
chuck as far as it will go, then back the shank
6
6
(1613EVS & 1614EVS)
RPM
RPM
Material
12,000
12,000
nonferrous metals,
14,000
14,500 larger diameter router
16,000
17,000
bits and cutters.
18,000
19,500 Softwoods, plastics,
20,000
22,000 counter tops, smaller
22,000
23,000
diameter router bits
and cutters.
"Soft Start" Feature
(1613EVS & 1614EVS )
!
Always disconnect the tool
Installing a Router Bit
12/7/98, 10:29 AM